Bedienungsanleitung Onkyo HT-R990 (Seite 31 von 172) (Englisch, Französisch)

462101

Zoom out

Zoom in

Vorherige Seite

1/172

Nächste Seite

Note

• You can cancel Audyssey 2EQ Room Correction and Speaker

Setup at any point in this procedure simply by disconnecting the

setup microphone.

• Do not connect or disconnect any speakers during

Audyssey 2EQ Room Correction and Speaker Setup.

• If the AV receiver is muted, it will be unmuted automatically

when Audyssey 2EQ Room Correction and Speaker Setup

starts.

• Changes to the room after Audyssey 2EQ Room Correction and

Speaker Setup requires you run Audyssey 2EQ Room

Correction and Speaker Setup again, as room EQ characteristics

may have changed.

When you’ve finished making the settings, press

ENTER.

Perform the “Speaker Setup” according to your

speaker configuration:

– Powered Zone 2 (➔ page 43)

– Surround Back/Front High (➔ page 44)

When an optional unit is connected to the

UNIVERSAL PORT jack on the AV receiver, the

optional unit setting may appear on the speaker

setting menu.

Use q/w to select “Audyssey Quick Start” or

“Audyssey 2EQ Full Calibration”.

Press ENTER.

Audyssey 2EQ

Room Correction and Speaker Setup

starts.

Test tones are played through each speaker as

Audyssey 2EQ Room Correction and Speaker Setup

runs. This process takes a few minutes. Please

refrain from talking during measurements and do

not stand between speakers and the microphone.

Do not disconnect the speaker setup microphone

during Audyssey 2EQ Room Correction and Speaker

Setup, unless you want to cancel the setup.

If you select “Audyssey Quick Start”, you will go to

step 9.

Place the setup microphone at the next position,

and then press ENTER.

Audyssey 2EQ performs more measurements. This

takes a few minutes.

When prompted, repeat step 7.

Use q/w to select an option, and then press

ENTER.

The options are:

` Save:

Save the calculated settings and exit

Audyssey 2EQ Room Correction and Speaker

Setup

` Cancel:

Cancel Audyssey 2EQ

Room Correction and

Speaker Setup

Note

• You can view the calculated settings for the speaker

configuration, speaker distances, and speaker levels by

using e/r.

2EQ: Auto Setup

AUDYSSEY

Powered Zone 2 No

Surround Back/Front High Surround Back

Subwoofer : Yes

Front : Yes

Center : Yes

Surround : Yes

Front High : No

Surround Back : Yes

Surround Back Ch : 2ch

Save

Cancel

AUDYSSEY

-- Review Speaker Configuration --

2EQ: Auto Setup

Use q/w to select a target, and use e/r to change

the setting.

After the results of Audyssey 2EQ have been saved,

the menu will display the “Audyssey” (➔ page 48),

“Dynamic EQ” (➔ page 48), “Dynamic Volume”

(➔ page 49) settings.

Note

•When “Audyssey Quick Start” has been used for

measurement, “Audyssey” cannot be selected.

• These settings are applied to all input selectors.

Press ENTER.

Disconnect the speaker setup microphone.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo HT-R990 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo HT-R990

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info