Bedienungsanleitung Onkyo HT-R990 (Seite 45 von 172) (Englisch, Französisch)

462101

Zoom out

Zoom in

Vorherige Seite

1/172

Nächste Seite

Level Calibration

Here you can adjust the level of each speaker with the

built-in test tone so that the volume of each speaker is the

same at the listening position.

■ Left, Front High Left, Center

, Front High Right,

Right, Surround Right, Surround Back Right,

Surround Back Left, Surround Left

` –12dB to 0dB to +12dB in 1 dB steps.

■ Subwoofer

` –15dB to 0dB to +12dB in 1 dB steps.

Note

• These settings cannot be calibrated in either of the following

cases:

– a pair of headphones is connected.

–the “Audio TV Out” setting is set to “On” (➔ page 55).

–“HDMI Control(RIHD)” is set to “On” (➔ page 54) and

you’re listening through your TV speakers.

– the AV receiver is muted.

• Speakers that you set to “No” in the “Speaker Configuration”

cannot be selected (➔ page 44).

• The test tone is output at the standard level for THX, which is

0 dB (absolute volume setting 82). If you normally listen at

volume settings below this, be careful because the test tone will

be much louder.

For the center speaker and subwoofer, the level settings made

by using the Home menu are saved in this menu

(➔ page 39).

Tip

• If you’re using a handheld sound level meter, adjust the level of

each speaker so that it reads 75 dB SPL at the listening position,

measured with C-weighting and slow reading.

Equalizer Settings

With the Equalizer settings, you can adjust the tone of

speakers individually with a 5-band equalizer. The volume

of each speaker can be set.

■ Equalizer

` Manual:

You can adjust the equalizer for each speaker

manually. Continue with the following procedure:

` Off

Tone off, response flat.

Note

• You can select: “63Hz”, “250Hz”, “1000Hz”, “4000Hz”, or

“16000Hz”. And for the subwoofer, “25Hz”, “40Hz”, “63Hz”,

“100Hz”, or “160Hz”.

• When the Direct listening mode is selected, the equalizer

settings have no effect.

• If “Audyssey” is enabled, it prevails over this setting

(➔ page 48).

This setting is set automatically by Audyssey 2EQ

Room Correction and Speaker Setup (➔ page 30).

Adjust the level control of the subwoofer to the THX

POSITION before calibrating this system.

Press w to select “Channel”, and then use

e/r to select a speaker.

Use q/w to select a frequency, and then use

the e/r to adjust the level at that frequency.

The volume at each frequency can be adjusted

from –6dB to 0dB

to +6dB in 1 dB steps.

Tip

• Low frequencies (e.g., 63Hz) affect bass sounds;

high frequencies (e.g., 16000Hz) affect treble

sounds.

Use q to select “Channel”, and then use e/r

to select another speaker.

Repeat steps 1 and 2 for each speaker.

You cannot select speakers that you set to “No”

in the “Speaker Configuration” (➔ page 44).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo HT-R990 Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo HT-R990

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info