Bedienungsanleitung Onkyo PA-MC5501 (Seite 10 von 20) (Englisch)

492658

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

b INPUT SELECT switch

This switch is located between the balanced input and

single-ended RCA input for each channel. Use this

switch to select the input type for its channel.

When setting the switch to the upper side, the

balanced input is selected.

When setting the switch to the lower side, the RCA

audio input is selected.

Note

• Do not change the INPUT SELECT switch setting when the

amplifier is turned on.

• Make sure that connections have been made only to the inputs

selected with the INPUT SELECT switches and nothing is

connected to the other ones.

c Unbalanced Input (single end RCA input)

Connect AV controllers or control amplifiers with

single-ended outputs.

Note

• When using this single-ended connection for a specific channel,

set the INPUT SELECT switch to the lower side (the RCA

audio input side), use commercial RCA audio pin cable and

connect the single-ended outputs.

• Do not connect anything to the balanced input jack.

d OUTPUT (Speaker output and binding post)

These terminal posts are for connecting the front L/R,

center, surround L/R, surround back L/R, and

front high/wide L/R speakers.

The FRONT L/R and FRONT HIGH/WIDE L/R

terminal posts can be used with front speakers and

front high/wide respectively, or used to bi-amp the

front speakers. See “Bi-amping the Front Speakers”

(➔ page 15).

e SPEAKER IMPEDANCE switch

Use this switch to select the speaker impedance.

f AUTO STANDBY switch

You can use the auto standby function. If the amplifier

receives no signal for 3 hours, it will automatically

enter standby mode. Once the auto standby function

has been activated, the amplifier will not

automatically turn on even if it receives the signal. To

turn on the amplifier, press the 8ON/STANDBY

button manually. You can also disable the function by

setting this switch to OFF side.

Default setting: ON (European models), OFF

(North American and Asian models)

Note

• Regardless of the position of this switch, this function will not

work when the amplifier has been turned on by the 12V trigger.

• Before entering standby mode by the auto standby function, the

amplifier notifies you by flashing the ON indicator for

10 seconds.

• Depending on some sources, the auto standby function may

activate during playback.

g 12V TRIGGER IN

Connects to the 12V trigger output terminal on the

other component to control the amplifier. This enables

the amplifier to turn on or go into standby state based

on the power on/standby status of the connected

component.

Use the supplied or commercially available 1/8-inch

mono cable to connect to the 12V trigger output

terminal on the other device.

The tip polarity of the connectors are as shown below.

h AC INLET

Plug the supplied power cord into this AC INLET and

then into the power outlet on the wall.

• Do not plug the amplifier into the AC outlet other than

an AC wall socket.

• Do not use a power cord other than the one supplied with

the amplifier. The power cord supplied is designed for

use with the amplifier and should not be used with any

other device.

• Never have the power cord disconnected from the

amplifier while the other end is plugged into the wall

outlet. Doing so may cause an electric shock. Always

connect by plugging into the wall outlet last and

disconnect by unplugging from the wall outlet first.

• Before you plug in the amplifier, confirm that all

connections have been made properly.

• Turning on the power may cause a momentary power

surge, which might interfere with other electrical

equipment on the same circuit, such as computers. If this

happens, use a wall outlet on a different circuit.

4Ω: Select if the impedance of any speaker is 4 ohms

or more but less than 6.

6Ω: Select if the impedances of all speakers are

between 6 and 16 ohms.

RCA type

5 to 12 volts, positive

tip polarity

To an AC

wall outlet

Power cord

(supplied)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo PA-MC5501 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo PA-MC5501

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info