Bedienungsanleitung Onkyo PA-MC5501 (Seite 11 von 20) (Englisch)

492658

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Connections

Connecting the Amplifier

Before connecting the speakers, place them correctly by

consulting the instruction manuals that came with them.

For surround playback, the configuration and placement

of your speakers are very important.

Please note that connecting speakers with a low power

input rating does not produce large sound volumes. For

those speakers, large sound volumes causing excessive

input level may damage the speakers.

Note

• Once you’ve completed speaker connections, you must turn

on the AV controller or control amplifier and configure the

output channels.

Attaching the Speaker Labels

The amplifier’s positive (+) speaker terminals are all red

(the negative (–) speaker terminals are all black).

The supplied speaker cable labels are also color-coded and

you should attach them to the positive (+) side of each

speaker cable in accordance with the above table. Then all

you need to do is to match the color of each label to the

corresponding speaker terminal.

(North American models)

• If you are using banana plugs, tighten the speaker

terminal before inserting the banana plug.

• Do not insert the speaker code directly into the center

hole of the speaker terminal.

Speaker Connection Precautions

Read the following before connecting your speakers:

• You can connect speakers with an impedance of between

4 and 16 ohms. If the impedance of any of the connected

speakers is 4 ohms or more, but less than 6 ohms, be sure

to set the minimum speaker impedance to “4Ω”

(➔ page 10). If you use speakers with a lower

impedance, and use the amplifier at high volume levels

for a long period of time, the built-in protection circuit

may be activated.

• Disconnect the power cord from the wall outlet before

making any connections.

• Read the instructions supplied with your speakers.

• Pay close attention to speaker wiring polarity. In other

words, connect positive (+) terminals only to positive (+)

terminals, and negative (–) terminals only to negative (–)

terminals. If you get them the wrong way around, the

sound will be out of phase and will sound unnatural.

• Unnecessarily long, or very thin speaker cables may

affect the sound quality and should be avoided.

• If you use 4 or 5 speakers, connect each of the two

surround speakers to the SURROUND L/R terminals.

Do not connect them to the SURR BACK L/R or

FRONT HIGH/WIDE L/R terminals.

• Be careful not to short the positive and negative wires.

Doing so may damage the amplifier.

• Make sure the metal core of the wire does not have

contact with the amplifier’s rear panel. Doing so may

damage the amplifier.

• Don’t connect more than one cable to each speaker

terminal. Doing so may damage the amplifier.

• Don’t connect one speaker to several terminals.

Connecting Your Speakers

Speaker Color

Front left White

Front right Red

Center Green

Surround left Blue

Surround right Gray

Surround back left Brown

Surround back right Tan

Front high/wide left White

Front high/wide right Red

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo PA-MC5501 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo PA-MC5501

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info