Bedienungsanleitung Onkyo TX-8522 (Seite 31 von 36) (Englisch)

66920

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Connecting Components not Reached by the Remote

Controller Signals (IR IN/OUT)

In order to use the remote controller to control the

receiver from a remote location, you will need to

prepare a multiroom kit (sold separately) such as one

listed below:

• Onkyo’s Multi-Room System kits (IR Remote

Controller Extension System)

• Multiroom A/V distribution and control system such

as those from Niles

and Xantech

* Xantech is a registered trademark of Xantech Corporation.

* Niles is a registered trademark of Niles Audio Corporation.

Effective Sensor Layout

Example for the main room

If the receiver is located inside a cabinet or other

enclosure where the infrared rays from the remote

controller cannot enter, then operation with the remote

controller will not be possible. In such a case, it will be

necessary to install a remote sensor at a location outside

of the cabinet so that the infrared rays from the controller

can be sensed.

Example for the remote zone

The IR IN input allows you to control the receiver from

the remote zone with the remote controller even though

the remote zone may be on the other side of the building

from the main zone. The diagram below shows how to

make the proper connections for the remote zone.

Making Sensor Connections

When you place the IR receiver in the main room, connect

the cable from the connecting block to the IR IN terminal.

Make the connection as shown below. Do not plug any

equipment into the power outlet until all the connections

are complete.

Effective Sensor Layout

In this situation, you will need to use a commercially

available IR emitter. Connect the mini plug of the IR

emitter to the IR OUT terminal on the receiver and then

place the IR emitter on the remote sensor of the

component or facing it. When the IR emitter is

connected, only the signal input to the IR IN terminal is

output to the IR OUT terminal. The signal input from the

remote sensor on the front of the receiver will not be

output to the IR OUT terminal.

Making Sensor Connections

When you place the IR receiver in the main room, connect

the cable from the connecting block to the IR OUT terminal.

If Remote Controller Signal Does not

Reach the Receiver Remote Sensor

Connecting

block

IR Receiver

Remote controller

IR IN

TX-8522/

TX-8222

In the

cabinet

: Signal ﬂow

Main room

IR Receiver

Remote controller

Connecting

block

Receiver

Main room Remote Zone

: Signal ﬂow

To IR IN

If Remote Controller Signal Does not

Reach Other Components

Receiver

from connecting block

Mini plug cable

IR Receiver

Remote controller

Connecting

block

IR IN

IR OUT

IR Emitter

Receiver

Other

component

: Signal ﬂow

Other component

Emitter

Remote control

sensor

IR Emitter

Mini plug

Receiver

TX-85228222_En.book 31 ページ２００６年５月４日木曜日午前１１時５１分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-8522 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-8522

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info