Bedienungsanleitung Onkyo TX-8522 (Seite 33 von 36) (Englisch)

66920

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Troubleshooting

—Continued

The remote controller doesn’t work

• Make sure that the batteries are installed with the cor-

rect polarity (page 5).

• Install new batteries. Don’t mix different types of bat-

teries or old and new batteries (page 5).

• Make sure that the remote controller is not too far

away from the receiver, and that there’s no obstruction

between the remote controller and the receiver’s

remote control sensor (page 10).

• Make sure that the receiver is not subjected to direct

sunshine or inverter-type ﬂorescent lights. Relocate if

necessary (page 10).

Can’t control other components

• If you’ve connected an -capable Onkyo DS-A1

Remote Interactive Dock to the TAPE 1 or VIDEO

jacks on the TX-8522 (or TAPE 1 or LINE 2 jacks on

the TX-8222), for the remote controller to work prop-

erly, you must set the input display to HDD (see

page 20).

• If it’s an Onkyo component, make sure that the

cable and analog audio cable are connected properly.

Connecting only an cable won’t work (page 19).

• With some components, certain buttons may not work

as expected, and some may not work at all.

• To control an Onkyo component that’s connected via

, point the remote controller at the receiver.

Can’t record

• On your recorder, make sure the correct input is

selected.

• To prevent signal loops and damage to the receiver,

input signals are not fed through to outputs with the

same name (e.g., TAPE IN to TAPE OUT, or VIDEO

IN to VIDEO OUT).

• When the Pure Audio function is selected, recording is

not possible because no video signals are output. Dis-

able the function before recording.

The display doesn’t work

• The display is turned off when the Pure Audio

(TX-8522) function is selected.

The functions don’t work

• To use , you must make an connection and an

analog audio connection (RCA) between the compo-

nent and receiver, even if they are connected digitally

(page 19).

Remote Controller

Recording

Others

The receiver contains a microcomputer for signal

processing and control functions. In very rare

situations, severe interference, noise from an external

source, or static electricity may cause it to lockup. In the

unlikely event that this happens, unplug the power cord

from the wall outlet, wait at least ﬁve seconds, and then

plug it back in again.

Onkyo is not responsible for damages (such as CD

rental fees) due to unsuccessful recordings caused by

the unit’s malfunction. Before you record important

data, make sure that the material will be recorded

correctly.

Before disconnecting the power cord from the wall

outlet, set the receiver to Standby.

Memory Backup

The receiver uses a battery-less memory backup

system in order to retain radio presets and other

settings when it’s unplugged or in the case of a power

failure. Although no batteries are required, the receiver

must be plugged into an AC outlet in order to charge the

backup system. Once it has been charged, the receiver

will retain the settings for several weeks, although this

depends on the environment and will be shorter in

humid climates.

TX-85228222_En.book 33 ページ２００６年５月４日木曜日午前１１時５１分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-8522 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-8522

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info