Bedienungsanleitung Onkyo TX-DS787 (Seite 35 von 76) (Englisch)

553756

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Input Setup

a. Digital Input

This setting tells the TX-DS787 which input source button on the

front panel is connected with which digital input jack on the rear

panel. To perform this setting, you must first select a digital input

source at the front panel and then set the name of the digital input

jack it is connected to here.

For example, if the input source selected at the front panel is CD

and the compact disc player is connected to DIGITAL INPUT

(OPTICAL) 1, then select “OPT1” here. If the input source

selected is not connected to a digital input, then select “----.”

OPT1: Select if connected to DIGITAL INPUT (OPTICAL) 1.

OPT2: Select if connected to DIGITAL INPUT (OPTICAL) 2.

COAX1: Select if connected to DIGITAL INPUT (COAXIAL) 1.

COAX2: Select if connected to DIGITAL INPUT (COAXIAL) 2.

––––: Select if the input source is not from a digital input jack.

Note:

Do not assign a digital input to more than one input source. If you

are making a digital connection that requires you to change the

default settings, be sure to always first cancel the current digital

input setting and then assign the new setting.

b. Digital Format

The default setting is “All.” If “----” is selected for this input

source at the Digital Input setting, then this setting will not appear.

Although you can use this default setting as is, you may change it

as desired depending on the input signal format (e.g., if you know

that you will always be listening to a certain input signal format

from a particular input source).

All: Select for automatic detection of the input signal format. The

input signal format (Dolby Digital, DTS, PCM or Analog)

used by the selected input source is detected automatically to

execute the required decoding process.

DTS: Select for DTS signal processing. The decoding process is

executed only when DTS signals are input.

PCM: Select for PCM signal processing. The decoding process is

executed only when PCM signals are input.

Note:

If “All” is selected and a compact disc or LD is fast-forwarded

during playback, decoded PCM signals may produce a skipping

sound. In such cases, change the setting to “PCM.”

Notes on DTS:

• If you play a CD or LD that supports DTS when the “PCM”

setting is selected on the TX-DS787, the DTS encoded signal

will not be decoded and noise will be output. This noise could

damage the amplifier and speakers. Therefore, be sure to

selected “All” or “DTS” and use the digital input jacks

(OPTICAL or COAXIAL) to connect the DTS source.

• If you play a CD or LD that supports DTS when “All” is

selected, you may hear a noise for a short while until the DTS

decoder recognizes the DTS-encoded signal and starts

operating. This is not a malfunction.

• If you press the PAUSE or SKIP button on the player while

playing a DTS source, a short noise may be heard. This is not a

malfunction. In such cases, try playing the source in the “DTS”

selected.

• The DTS indicator on the TX-DS787 lights while a DTS

source is played. When playback finishes and the DTS signal

transmission stops, the TX-DS787 remains in DTS mode and

the DTS indicator remains lit. This prevents noise when you

operate the PAUSE or SKIP button on the player. Therefore, if

the source is immediately switched from DTS to PCM, the

PCM signal may not be played. In this case, stop the playback

of the source on the player for about three seconds and then

resume playback.

• You may not be able to play some DTS source signals from

certain CD players and LD players even if you connect the

player to the TX-DS787 digitally. This is because the digital

signal has been processed (such as the output level, sampling

frequency, or frequency response) and the TX-DS787 cannot

recognize the signal as DTS data. Therefore you may hear

noise when you play a DTS source while processing the signal.

• The outputs for the VIDEO 1 OUT, VIDEO 2 OUT, TAPE

OUT, output analog audio signals. Do not record from CDs or

LDs that support DTS using these outputs. If you do, the DTS-

encoded signal will be recorded as noise.

• If a compact disc or LD encoded in the DTS format is played

back with “PCM” selected, only noise will be produced.

Always select “All” or “DTS” when playing back DTS-

encoded sources.

c. Multichannel

This sub-menu will not appear if AM or FM is selected at the front

panel for the input source. This setting is normally set to “No,” and

only needs to be changed to “Yes” if a DVD player, MPEG

decoder, or other component that has a multi channel port is

connected to the MULTI CHANNEL INPUT port for 5.1-channel,

6.1-channel, or 7.1-channel audio. For example, if a DVD player is

connected to the MULTI CHANNEL INPUT port, then select

DVD at the front panel as the input source, bring up this sub-menu,

and select “Yes” for the Multichannel setting. You can only select

Multichannel with the AUDIO SELECTOR button when “Yes” is

selected here.

Note:

When playing a device that is actually connected to the MULTI

CHANNEL INPUT terminal, select Multichannel with the

AUDIO SELECTOR button.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-DS787 Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-DS787

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info