Bedienungsanleitung Onkyo TX-L55 (Seite 31 von 63) (Englisch)

645294

Zoom out

Zoom in

Vorherige Seite

1/63

Nächste Seite

Basic Setup

—Continued

Notes:

• This procedure can also be performed by using the

[SETUP] button. Press the REMOTE MODE [AMP]

button followed by the [SETUP] button. Use the Up

and Down [ ]/[ ] buttons to select “Level Cal,” and

then press [ENTER]. Use the Left and Right [ ]/[ ]

buttons to adjust the speaker volume, and use the

Down [ ] button to select the next speaker. Unlike the

above procedure, the next speaker will not be selected

automatically after two seconds.

Digital Audio Input Setup

To enjoy Dolby Digital and DTS, you must connect your

DVD player to the TX-L55 by using a digital audio con-

nection (coaxial or optical).

This section explains how to change the digital audio

input socket to input source assignments. You only need

to change them if your connections don’t match the

defaults listed in the following table.

For example, if you connect your DVD player to the

OPT 1 DIGITAL INPUT, you’ll need to change the

DVD input source from COAX to OPT 1.

If you want to use the TV input source with only the

analog TV IN, change the TV input source assignment

from OPT1 to “----” (Analog).

You can change the assignments as follows.

Use the [CH SEL] button to select

the speakers, and use the

[LEVEL+] and [LEVEL–] buttons

to adjust the volume.

The level can be adjusted from –12 to

+12 dB in 1 dB steps.

If you don’t press anything for two sec-

onds, the next speaker will be selected

automatically.

Repeat step 3 until the volume of

the test tone coming from each

speaker is the same.

Speakers that you set to No or Non in

the Speaker Conﬁguration (page 48) do

not output the test tone.

Press the [TEST TONE] button.

The setup menu closes.

Don’t forget to turn down the volume if

you turned it up while setting the levels.

Assigning Inputs to Input Sources

Input source Default digital input assignment

DVD COAX

TV OPT1

VIDEO1 OPT2

VIDEO2 - - - - (Analog)

AUX- - - - (Analog)

LEVEL LEVEL

CH SEL

TEST TONE

Press the REMOTE MODE [AMP]

button followed by the [INPUT

SELECTOR] button for the input

source whose assignment you

want to change.

There is no assignment for the TUNER

input source.

Press the [SETUP] button.

Use the Up and Down [ ]/[ ]

buttons to select “Input Set,” and

then press [ENTER].

Use the Up and Down [ ]/[ ]

buttons to select “Digital In,” and

then use the Left and Right [ ]/

[] buttons to select:

COAX:

Select if the component is

connected to the COAX DIG-

ITAL INPUT.

OPT1:

Select if the component is

connected to the OPT1 DIGI-

TAL INPUT.

OPT2:

Select if the component is

connected to the OPT2 DIGI-

TAL INPUT.

Press the [SETUP] button.

The setup menu closes.

AMP

TUNER

TV AUX

TUN

DVD

INPUT SELECTOR

ENTER

TX-L55_En.book Page 31 Tuesday, June 1, 2004 9:02 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-L55 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info