Bedienungsanleitung Onkyo TX-NR 717 (Seite 47 von 148) (Englisch)

492647

Zoom out

Zoom in

Vorherige Seite

1/148

Nächste Seite

Turning On & Basic Operations

En-47

You can set which speakers you want to use by priority.

Note

• This setting is not available in either of the following cases:

–The “Speakers Type(Front)” setting is set to “Bi-Amp”.

–The “Powered Zone 2/3” setting is set to “Yes” and Zone 2/3

is turned on.

• Playback conditions may be limited depending on the settings in

“Speaker Settings” (➔ page 55) and

“Speaker Configuration”(➔ page 55).

• When a listening mode which doesn’t support front high, front

wide or surround back speakers is used, this setting cannot be

selected.

The Whole House Mode is useful when you want to add

extra background music to your home party; this allows

you to enjoy the same stereo music as the main room in

separate rooms (Zone 2/3).

The Whole House Mode selects the same input source for

Multi Zone as the main room’s.

See also:

• “Speaker Setup” (➔ page 55)

• “Multi Zone” (➔ page 70)

You can temporarily mute the output of the AV receiver.

Selecting Speaker Layout

Press RECEIVER followed by SP (speaker layout)

repeatedly to select:

` Speaker Layout:FH:

The sound from front high speakers is output by

priority.

` Speaker Layout:FW:

The sound from front wide speakers is output by

priority.

` Speaker Layout:SB:

The sound from surround back speakers is

output by priority.

Using the Whole House Mode

While holding down ZONE 2, press ZONE 3 on the

front panel.

To cancel the Whole House Mode, change the input

source for the main room or select a listening mode

(➔ page 38).

Note

• The Whole House Mode only supports analog audio.

• To adjust the volume of Multi Zone, switch the AV receiver

to Multi Zone control. See “Adjusting the Volume for

Zones” (➔ page 71) for the volume adjustment of Multi

Zone.

• The Whole House Mode is not available in either of the

following cases:

–The “Audio TV Out” setting is set to “On”

(➔ page 67).

–“HDMI Control(RIHD)” is set to “On” (➔ page 67)

and you’re listening through your TV speakers.

Muting the AV Receiver

Press RECEIVER followed by MUTING.

The output is muted and the MUTING indicator

flashes on the AV receiver’s display.

Tip

• To unmute, press MUTING again or adjust the volume.

• Muting is automatically cancelled when the AV receiver is

set to standby.

Using Headphones

Connect a pair of stereo headphones with a

standard plug (1/4 inch or 6.3 mm) to the PHONES

jack.

While the headphones plug is inserted in the PHONES

jack, = indicator lights.

Note

• Always turn down the volume before connecting your

headphones.

• While the headphones plug is inserted in the PHONES

jack, the speakers are turned off. (The Powered Zone 2/3

speakers are not turned off.)

• When you connect a pair of headphones, the listening mode

is set to Stereo, unless it’s already set to Stereo, Mono,

Direct, or Pure Audio.

• If you connect an iPod or iPhone to the USB port on the AV

receiver, no sound will be output from the headphones jack.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR 717 Seite 47

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR 717

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info