Bedienungsanleitung Onkyo TX-NR 717 (Seite 49 von 148) (Englisch)

492647

Zoom out

Zoom in

Vorherige Seite

1/148

Nächste Seite

Advanced Operations

En-49

Note

• The video preview is not displayed when:

– HDMI IN 5/6/7 is the current HDMI input source, or

– No signal is present on the current input source.

• The video of the currently-selected input is displayed on the

main screen, not on a preview thumbnail.

“Dynamic EQ” and “Dynamic Volume” cannot be selected

when any of the THX listening modes is selected, with

“Loudness Plus” set to “On” or “Preserve THX Settings” set

to “Yes” (➔ page 57).

• When the “Monitor Out” setting is set to “Sub”, “Video”

cannot be selected (➔ page 53).

• This setting cannot be used with the NET input selector.

Only when you have selected “Custom” in the “Picture

Mode” (➔ page 63), pressing ENTER allows you to adjust

the following items via the Quick Setup: “Brightness”,

“Contrast”, “Hue” and “Saturation”. Press RETURN to

return to the “Picture Mode” setting.

Depending on the input source and listening mode, not all

channels shown here output the sound.

• This setting is not available in either of the following cases:

–The “Audio TV Out” setting is set to “On” (➔ page 67).

–“HDMI Control(RIHD)” is set to “On” (➔ page 67) and

you’re listening through your TV speakers.

You can change various audio settings from the Quick

Setup (➔ page 48).

Note

• These settings are not available in either of the following cases:

–The “Audio TV Out” setting is set to “On” (➔ page 67).

–“HDMI Control(RIHD)” is set to “On” (➔ page 67) and

you’re listening through your TV speakers.

Tone Control

■ Bass

` –10dB to 0dB

to +10dB in 2 dB steps

You can boost or cut low-frequency sounds output

from the front speakers.

■ Treble

` –10dB to 0dB

to +10dB in 2 dB steps

You can boost or cut high-frequency sounds output

from the front speakers.

You can adjust the bass and treble for the front speakers,

except when the Direct, Pure Audio or THX listening

mode is selected.

Operating on the AV receiver

Speaker Levels

■ Subwoofer Level

` –15.0dB to 0.0dB

to +12.0dB in 0.5 dB steps

■ Center Level

` –12.0dB to 0.0dB to +12.0dB in 0.5 dB steps

You can adjust the volume of each speaker while listening

to an input source.

These temporary adjustments are cancelled when the AV

receiver is set to standby. To save the setting you made

here, go to “Level Calibration” (➔ page 56) before

setting the AV receiver to standby.

Note

• You cannot use these function while the AV receiver is muted.

• These settings cannot be used while a pair of headphones is

connected.

• Speakers that are set to “No” or “None” in

“Speaker Configuration” (➔ page 55) cannot be adjusted.

Using the Audio Settings of Quick

Setup

Press TONE repeatedly to select either “Bass” or

“Treble”.

Use – and + to adjust.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR 717 Seite 49

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR 717

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info