Bedienungsanleitung Onkyo TX-NR 717 (Seite 68 von 148) (Englisch)

492647

Zoom out

Zoom in

Vorherige Seite

1/148

Nächste Seite

Advanced Operations

En-68

Note

• This setting is fixed to “----” when the “HDMI

Control(RIHD)” setting is set to “Off”.

• This setting is set to “Auto” automatically when the “HDMI

Control(RIHD)” setting is set to “On” for the first time.

• If you set “Audio Return Channel” to “Auto”, the “Audio

Selector” settings of the TV/CD input selector will be

automatically switched to “ARC” (➔ page 64).

■ LipSync

` Off

` On

This function allows the AV receiver to automatically

correct any delay between the video and the audio, based

on the data from the connected monitor.

Note

• This function works only if your HDMI-compatible TV supports

HDMI Lip Sync.

■ InstaPrevue

These settings apply to “InstaPrevue” of the Home menu

(➔ page 45) and specify the preview display of HDMI

video streams.

Sub Window

` Multi

Displays preview thumbnails all at once.

` Single:

Displays preview thumbnails one-by-one.

With this setting, you can set the number of preview

thumbnails displayed.

Position

(with “Sub Window” set to “Multi”)

` Top, Bottom

, Left, Right

(with “Sub Window” set to “Single”)

` Upper Left, Upper Right, Lower Left, Lower Right

With this setting, you can set the position of preview

thumbnails on the TV screen.

Note

• Depending on video signals, the picture may not be properly

rendered on the preview thumbnails of InstaPrevue.

Auto Standby

■ Auto Standby

` Off

` On

When “Auto Standby” is set to “On”, the AV receiver

will automatically enter standby mode if there is no

operation for 30 minutes with no audio and no video signal

input.

“Auto Standby” will appear on the AV receiver’s display

and OSD 30 seconds before the Auto Standby comes on.

Default setting: On (European, Australian and Asian

models), Off (North American and Taiwanese models)

Note

•Set to “

On”, the Auto Standby function may activate itself during

playback with some sources.

•The Auto

Standby function does not work when Zone 2/3 is on.

Network

This section explains how to configure the AV receiver’s

network settings manually.

If your router’s DHCP server is enabled, you don’t need to

change any of these settings, as the AV receiver is set to

use DHCP to configure itself automatically by default (i.e.,

DHCP is set to “Enable”). If, however, your router’s

DHCP server is disabled (you’re for example using static

IP), you’ll need to configure these settings yourself, in

which case, a knowledge of Ethernet networking is

essential.

What’s DHCP?

DHCP (Dynamic Host Configuration Protocol) is used by

routers, computers, the AV receiver, and other devices to

automatically configure themselves on a network.

What’s DNS?

The DNS (Domain Name System) translates domain

names into IP addresses. For example, when you enter a

domain name such as www.onkyousa.com in your Web

browser, before accessing the site, your browser uses DNS

to translate this into an IP address, in this case

63.148.251.142.

■ MAC Address

This is the AV receiver’s MAC (Media Access Control)

address. This address cannot be changed.

■ DHCP

` Enable

` Disable

This setting determines whether or not the AV receiver

uses DHCP to automatically configure its IP Address,

Subnet Mask, Gateway, and DNS Server settings.

Note

• If you select “Disable”, you must configure the “IP Address”,

“Subnet Mask”, “Gateway”, and “DNS Server” settings

yourself.

After changing the settings of the “HDMI

Control(RIHD)”, “HDMI Through” or “Audio

Return Channel”, turn off the power on all connected

pieces of equipment and then turn them on again. Refer

to the user’s manuals for all connected pieces of

equipment.

After modifying the network settings, you must confirm

the changes by executing “Save”.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR 717 Seite 68

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR 717

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info