Bedienungsanleitung Onkyo TX-NR3008 (Seite 33 von 116) (Englisch)

553767

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

Note

• Make the room as quiet as possible. Background noise and Radio

Frequency Interference (RFI) can disrupt the room measure-

ments. Close windows, televisions, radios, air conditioners, flu-

orescent lights, home appliances, light dimmers, or other

devices. Turn off the cell phone (even if it is not in use) or place

it away from all audio electronics.

• The microphone picks up test tones which played through each

speaker as Audyssey MultEQ

XT32 Room Correction and

Speaker Setup run.

• Audyssey MultEQ XT32 Room Correction and speaker setup

can only be used with Speakers A. When you insert the MIC

with Speakers B selected, Speakers A will automatically be

selected.

• Audyssey MultEQ XT32 Room Correction and speaker setup

cannot be performed while a pair of headphones is connected.

Turn on the AV receiver and the connected TV.

On the TV, select the input to which the AV receiver

is connected.

Set the speaker setup microphone at the Main Lis-

tening Position a, and connect it to the SETUP

MIC jack.

The speaker setting menu appears.

When you’ve finished making the settings, press

ENTER.

• If you change “Speakers Type(Front A)” or

“Speakers Type(Front B)” setting, refer to

“Speaker Settings” for more details (➔ 50).

• If you change “Powered Zone 2” or “Powered

Zone 3” setting, refer to “Setting the Powered

Zone 2/3” for more details (➔ 82).

• If you are using a subwoofer(s), select “1ch” or

“2ch” in the “Subwoofer” (➔ 51). If not, select

“No” and skip step 4.

cab

: Listening area

a to h: Listening position

Speaker setup microphone

SETUP MIC jack

MultEQ XT32: Auto Setup

Speakers Type(Front A)

Speakers Type(Front B)

Powered Zone 2

Powered Zone 3

Normal

Not Use

Not Act

If you use a powered subwoofer(s), adjust the sub-

woofer volume level to 75dB.

Test tones are played through the subwoofer. Use the

volume control on the subwoofer.

Caution

•When the “Subwoofer” setting is set to “1ch”, the left-

hand subwoofer (SW1) alone will be measured.

When the “Subwoofer” setting is set to “1ch” with two

subwoofers connected, the right-hand subwoofer (SW2)

will not be measured and no sound will be output.

• An error will occur if you set “Subwoofer” to “2ch” with-

out connecting any subwoofers, or with only one sub-

woofer connected.

Note

• If your subwoofer does not have a volume control, disre-

gard the level displayed and press ENTER to proceed to

the next step.

• If you set the subwoofer’s volume control to its maximum

and the displayed level is lower than 75 dB, leave the sub-

woofer’s volume control at its maximum and press

ENTER to proceed to the next step.

Press ENTER.

Audyssey MultEQ XT32 Room Correction and

Speaker Setup starts.

Test tones are played through each speaker as

Audyssey MultEQ XT32 Room Correction and

Speaker Setup runs. This process takes a few min-

utes. Please refrain from talking during measure-

ments and do not stand between speakers and the

microphone.

Do not disconnect the speaker setup microphone

during Audyssey MultEQ XT32 Room Correction

and Speaker Setup, unless you want to cancel the

setup.

Place the setup microphone at the next position,

and then press ENTER.

Audyssey MultEQ XT32 performs more measure-

ments. This takes a few minutes.

When prompted, repeat step 6.

Use q/w to select an option, and then press

ENTER.

The options are:

` Save:

Save the calculated settings and exit

Audyssey MultEQ XT32

Room Correction and

Speaker Setup

` Cancel:

Cancel Audyssey MultEQ XT32

Room Correc-

tion and Speaker Setup

MultEQ XT32: Auto Setup

Subwoofer 2ch

Front 40Hz

Center 40Hz

Surround 100Hz

Front Wide None

Front High 100Hz

Surround Back 120Hz

Surround Back Ch 2ch

Save

Cancel

- - Review Speaker Configuration - -

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR3008 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR3008

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info