Bedienungsanleitung Onkyo TX-NR3008 (Seite 34 von 116) (Englisch)

553767

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

Note

• When Audyssey MultEQ

XT32 Room Correction and Speaker

Setup is complete, the “Equalizer” will be set to “Audyssey”

(➔ 53). The Audyssey indicator will light (➔ 9).

• You can cancel Audyssey MultEQ XT32 Room Correction and

Speaker Setup at any point in this procedure simply by discon-

necting the setup microphone.

• Do not connect or disconnect any speakers during

Audyssey MultEQ XT32 Room Correction and Speaker Setup.

• If the AV receiver is muted, it will be unmuted automatically

when Audyssey MultEQ XT32 Room Correction and Speaker

Setup starts.

• Changes to the room after Audyssey MultEQ XT32 Room Cor-

rection and Speaker Setup requires you run

Audyssey MultEQ XT32 Room Correction and Speaker Setup

again, as room EQ characteristics may have changed.

Error Messages

While Audyssey MultEQ XT32 Room Correction and

Speaker Setup is in progress, one of the error messages

below may appear.

The options are:

` Retry:

Try again.

` Cancel:

Cancel Audyssey MultEQ XT32 Room Correction

and Speaker Setup.

• Ambient noise is too high.

The background noise is too loud. Remove the source of

the noise and try again.

• Speaker Matching Error!

The number of speakers detected was different from

that of the first measurement. Check the speaker con-

nection.

•Writing Error!

This message appears if saving fails. Try saving again.

If this message appears after 2 or 3 attempts, contact

your Onkyo dealer.

•Speaker Detect Error

This message appears if a speaker is not detected. “No”

means that no speaker was detected.

Tip

• See “Speaker Configuration” for appropriate settings (➔ 14).

Changing the Speaker Settings Manually

You can manually make changes to the settings found dur-

ing Audyssey MultEQ XT32 Room Correction and

Speaker Setup.

See also:

• “Speaker Configuration” (➔ 51)

• “Speaker Distance” (➔ 52)

• “Level Calibration” (➔ 53)

• “Equalizer Settings” (➔ 53)

Note

• Please note that THX recommends any THX main speakers be

set to “80Hz(THX)”. If you set up your speakers using

Audyssey MultEQ XT32 Room Correction and Speaker

Setup, please make sure manually that any THX speakers are set

to 80 Hz (THX) crossover (➔ 51).

• Sometimes due to the electrical complexities of subwoofers and

the interaction with the room, THX recommends setting the level

and the distance of the subwoofer manually.

• Sometimes due to interaction with the room, you may notice

irregular results when setting the level and/or distance of the

main speakers. If this happens, THX recommends setting them

manually.

Using a Powered Subwoofer

If you’re using a powered subwoofer and it outputs very

low-frequency sound at a low volume level, it may not be

detected by Audyssey MultEQ XT32 Room Correction

and Speaker Setup.

If the “Subwoofer” appears on the “Review Speaker

Configuration” screen as “No”, increase the subwoofer’s

volume to the half-way point, set it to its highest crossover

frequency, and then try running Audyssey MultEQ XT32

Room Correction and Speaker Setup again. Note that if

the volume is set too high and the sound distorts, detection

issues may occur, so use an appropriate volume level. If

the subwoofer has a low-pass filter switch, set it to Off or

Direct. Refer to your subwoofer’s instruction manual for

details.

Note

• You can view the calculated settings for the speaker con-

figuration, speaker distances, and speaker levels by using

e/r.

Disconnect the speaker setup microphone.

Ambient noise is too high.

Retry

Cancel

MultEQ XT32: Auto Setup

Error message

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR3008 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR3008

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info