Bedienungsanleitung Onkyo TX-NR3008 (Seite 64 von 116) (Englisch)

553767

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

Main menu Hardware Setup

Remote ID

■ Remote ID

` 1

, 2, or 3

When several Onkyo components are used in the same

room, their remote ID codes may overlap. To differenti-

ate the AV receiver from the other components, you can

change its remote ID from “1”, to “2” or “3”.

Note

• If you do change the AV receiver’s remote ID, be sure to change

the remote controller to the same ID (see below), otherwise, you

won’t be able to control it with the remote controller.

Changing the Remote Controller’s ID

Multi Zone

See “Setting the Multi Zone” (➔ 83).

Tuner

For FM/AM tuning to work properly, you must specify the

FM/AM frequency step used in your area. Note that when

this setting is changed, all radio presets will be deleted.

■ FM/AM Frequency Step (North American

models)

` 200kHz/10kHz

Select if 200 kHz/10 kHz steps are used in your area.

` 50kHz/9kHz:

Select if 50 kHz/9 kHz steps are used in your area.

■ AM Frequency Step (European and Asian

models)

` 10kHz:

Select if 10 kHz steps are used in your area.

` 9kHz

Select if 9 kHz steps are used in your area.

SIRIUS Settings (North American models)

See the separate Satellite Radio Guide for more informa-

tion.

■ SAT Radio Mode

If you connect a SIRIUS Satellite Radio antenna to the

AV receiver (sold separately), set this setting to “SIR-

IUS”.

■ Antenna Aiming, SIRIUS Parental Lock

These items are for use with SIRIUS Satellite Radio.

It’s not available if “SAT Radio Mode” is set to

“None”.

HDMI

■ Audio TV Out

` Off

The audio is not output from the HDMI output.

` On:

The audio is output from the HDMI output.

This preference determines whether the incoming audio

signal is output from the HDMI output. You may want to

turn this preference on if your TV is connected to the

HDMI output and you want to listen to the audio from a

connected component through your TV’s speakers. Nor-

mally, this should be set to “Off”.

Note

• Listening mode cannot be changed when this setting is set to

“On” and the input source is not HDMI.

•If

“On” is selected and the audio can be output from the TV, the

AV receiver will output no sound through its speakers. In this

case, “TV Sp On” appears on the display.

•When

“TV Control” is set to “On”, this setting is fixed to

“Auto”.

• With some TVs and input signals, no sound may be output even

when this setting is set to

“On” (➔ 65).

•When the “Audio TV Out” setting is set to

“On”, or “TV Con-

trol” is set to

“On” (➔ 65) and you’re listening through your

TV’s speakers (➔ 21), if you turn up the AV receiver’s volume

control, the sound will be output by the AV receiver’s front left

and right speakers. To stop the AV receiver’s speakers producing

sound, change the settings, change your TV’s settings, or turn

down the AV receiver’s volume.

•If the “Monitor Out” setting is set to “Both(Main)” or

“Both(Sub)” (➔ 47) and if your TV connected to a priority out-

put cannot output the audio, the sound will be heard from AV

receiver’s speakers.

■ Lip Sync

` Disable

HDMI lip sync disabled.

` Enable:

HDMI lip sync enabled.

The AV receiver can be set to automatically correct any

delay between the video and the audio, based on the data

from the connected monitor.

Note

• This function works only if your HDMI-compatible TV supports

HDMI Lip Sync.

• You can check the amount of delay being applied by the HDMI

Lip Sync function on the A/V Sync screen.

•If the “Monitor Out” setting is set to “HDMI Main”,

“Both(Main)” or “Both” (➔ 47), the delay will be corrected in

accordance with the monitor connected to HDMI OUT MAIN.

On the other hand, if “HDMI Sub” or “Both(Sub)” is selected,

the delay will be corrected in accordance with the monitor con-

nected to HDMI OUT SUB.

Hardware Setup

While holding down RECEIVER, press and hold

down SETUP until RECEIVER lights (about 3

seconds).

Use the number buttons to enter ID 1, 2, or 3.

RECEIVER flashes twice.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR3008 Seite 64

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR3008

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info