Bedienungsanleitung Onkyo TX-NR3010 (Seite 43 von 168) (Englisch)

492661

Zoom out

Zoom in

Vorherige Seite

1/168

Nächste Seite

Turning On & Basic Operations

En-43

Turn on the AV receiver and the connected TV.

On the TV, select the input to which the AV receiver

is connected.

Set the speaker setup microphone at the Main

Listening Position a, and connect it to the SETUP

MIC jack.

The speaker setting menu appears.

Note

• The on-screen menus appear only on a TV that is connected

to HDMI OUT MAIN. If your TV is connected to other

video outputs, use the AV receiver’s display when changing

settings.

When you’ve finished making the settings, press

ENTER.

Perform the “Speaker Setup” according to your

speaker configuration:

– Speakers Type(Front A) (➔ page 66)

– Speakers Type(Front B) (➔ page 66)

– Powered Zone 2 (➔ page 66)

– Powered Zone 3 (➔ page 66)

– 11ch Playback (➔ page 66)

– Subwoofer (➔ page 67)

Speaker setup microphone

SETUP MIC jack

MultEQ XT32: Auto Setup

AUDYSSEY

Speakers Type(Front A)

Speakers Type(Front B)

Powered Zone 2

Powered Zone 3

11ch Playback

Subwoofer

Normal

2ch

If you use a powered subwoofer(s), go to step 4. If not,

go to step 5.

If “Speakers Type(Front A)” or “Speakers

Type(Front B)” is set to “Digital Crossover”, a

confirmation screen appears. Select “Next (2-7.

Digital Processing Crossover Network)” to display

the screen for Digital Processing Crossover Network

(➔ page 71). Continue with the settings.

Adjust the subwoofer volume level to 75 dB, and

then press ENTER.

Test tones are played through the subwoofer. Use the

volume control on the subwoofer.

When the “Subwoofer” setting is set to “1ch” only,

the left-hand subwoofer (SW1) will be measured.

When the “Subwoofer” setting is set to “1ch” with

two subwoofers connected, the right-hand subwoofer

(SW2) will not be measured and no sound will be

output.

An error will occur if you set “Subwoofer” to “2ch”

without connecting any subwoofers, or with only one

subwoofer connected.

Note

• If your subwoofer does not have a volume control, disregard

the displayed level and press ENTER to proceed to the next

step.

• If you set the subwoofer’s volume control to its maximum

and the level displayed is lower than 75 dB, leave the

subwoofer’s volume control at its maximum and press

ENTER to proceed to the next step.

• If you use two subwoofers, perform this step twice.

Use q/w to select “Audyssey Quick Start” or

“Audyssey MultEQ XT32 Full Calibration”, and

then press ENTER.

Press ENTER.

Audyssey MultEQ

XT32 Room Correction and

Speaker Setup starts.

Test tones are played through each speaker as

Audyssey MultEQ XT32 Room Correction and

Speaker Setup runs. This process takes a few minutes.

Please refrain from talking during measurements

and do not stand between speakers and the

microphone.

Do not disconnect the speaker setup microphone

during Audyssey MultEQ XT32 Room Correction and

Speaker Setup, unless you want to cancel the setup.

If you select “Audyssey Quick Start”, you will go to

step 9.

Place the speaker setup microphone at the next

position, and then press ENTER.

Audyssey MultEQ XT32 performs more

measurements. This takes a few minutes.

When prompted, repeat step 7.

To be continued

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR3010 Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR3010

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info