Bedienungsanleitung Onkyo TX-NR3010 (Seite 63 von 168) (Englisch)

492661

Zoom out

Zoom in

Vorherige Seite

1/168

Nächste Seite

Advanced Operations

En-63

Main Menu Input/Output Assign

Monitor Out

On the “Monitor Out” settings, you can select whether or

not to have the video sources’ images output through the

HDMI output.

If you connect your TV to the HDMI output, the “Monitor

Out” setting is automatically set and composite video and

component video sources are upconverted

and output.

If you connect your TV to the COMPONENT VIDEO

MONITOR OUT (not the HDMI output), “Monitor Out”

setting is automatically set and composite video source is

upconverted

and output.

Note

• See “Video Connection Formats” (➔ page 111) for charts

showing how the “Monitor Out” and “Resolution” settings

affect the video signal flow through the AV receiver.

■ Monitor Out

` Analog:

Select this if your TV is connected to the

COMPONENT VIDEO MONITOR OUT or

MONITOR OUT V.

` Main

Select this if your TV is connected to HDMI OUT

MAIN.

` Sub:

Select this if your TV is connected to HDMI OUT

SUB.

` Both:

Select this if your TVs are connected to HDMI OUT

MAIN and HDMI OUT SUB. Video signals are

output from both HDMI outputs at the resolution

supported by both TVs.

Changing the “Monitor Out” setting manually

■ Zone 2 HDMI

` Not Use

` Use

When this setting is enabled, the TV connected to HDMI

OUT ZONE 2 can be used as the TV of Zone 2.

Tip

• On the connected component, select the mode in which the delay

between the video and audio does not occur much if the video

signal delay occurs during the playback on the video component

connected to the AV receiver.

Note

• This setting cannot be selected if the “Monitor Out” setting is set

to “Sub” or “Both”.

• When this setting is set to “Use”, the “11ch Playback” setting is

fixed to “No” (➔ page 66).

■ Resolution

` Through

Select this to pass video through the AV receiver at

the same resolution and with no conversion.

` Auto

Select this to have the AV receiver automatically

convert video at resolutions supported by your TV.

` 480p (480p/576p), 720p, 1080i:

Select the desired output resolution.

` 1080p

Select this for 1080p output and video conversion as

necessary.

` 1080p/24

Select this for 1080p output at 24 frames per second.

` 4K Upscaling

Select this for an output resolution four times that of

1080p. Depending on the resolution supported by

your TV, it will result in either 3840 × 2160 or 4096

× 2160 pixels.

` Source:

Select this for an output following the resolution level

set in “Picture Adjust” (➔ page 78).

Input/Output Assign

1 2 3 4 5

“Setup”

OUT

Composite video,

component video

HDMI

Composite video,

component video

OUT

Composite video

Component video

Press MONITOR OUT on the front panel.

The current setting is displayed.

Press MONITOR OUT on the AV receiver

repeatedly to select:

` Analog, HDMI Main, HDMI Sub or Both.

To be continued

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR3010 Seite 63

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR3010

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info