Bedienungsanleitung Onkyo TX-NR3010 (Seite 66 von 168) (Englisch)

492661

Zoom out

Zoom in

Vorherige Seite

1/168

Nächste Seite

Advanced Operations

En-66

Main Menu Speaker Setup

Here you can check the settings made by

Audyssey MultEQ XT32 Room Correction and Speaker

Setup function, or set them manually, which is useful if

you change one of the connected speakers after using

Audyssey MultEQ XT32 Room Correction and Speaker

Setup function.

Press RECEIVER and use SP on the remote controller to

select Speakers A or Speakers B. For details on SP, see

“Selecting Speaker Layout” (➔ page 55).

Note

• These settings are not available in either of the following cases:

– a pair of headphones is connected.

–the “Audio TV Out” setting is set to “On” (➔ page 84).

–“HDMI Control(RIHD)” is set to “On” (➔ page 83) and

you’re listening through your TV speakers.

Speaker Settings

If the impedance of any speaker is 4 ohms or more but less

than 6, set the minimum speaker impedance to 4 ohms.

If you bi-amp the front speakers, you must change the

“Speakers Type(Front A)” or “Speakers

Type(Front B)” setting. For details on speaker wire

connection, see “Bi-amping the Front Speakers”

(➔ page 18). When connecting speakers without

crossover network, you need to change the “Speakers

Type(Front A)” or “Speakers Type(Front B)” setting

beforehand. For details on connection, refer to “Using

Speakers Without Crossover Network” (➔ page 18).

Note

• When bi-amping is used, the AV receiver is able to drive up to 7.2

speakers in the main room.

• Before you change these settings, turn down the volume.

■ Speaker Impedance

` 4ohms:

Select if the impedance of any speaker is 4 ohms or

more but less than 6.

` 6ohms

Select if the impedances of all speakers are between 6

and 16 ohms.

■ Speakers Type(Front A)

` Normal

Select this if you’ve connected your front speakers A

normally.

` Bi-Amp:

Select this if you’ve bi-amped your front speakers A.

` Digital Crossover:

Select this if you’re using speakers without crossover

network.

■ Speakers Type(Front B)

` No

Select this if you’re not using speakers B.

` Normal:

Select this if you’ve connected your front speakers B

normally.

` Bi-Amp:

Select this if you’ve bi-amped your front speakers B.

` Digital Crossover:

Select this if you’re using speakers without crossover

network.

Tip

• If “Speakers Type(Front A)” or “Speakers Type(Front B)” is

set to “Digital Crossover”, a confirmation screen appears. Select

“Next (2-7. Digital Processing Crossover Network)” to display

the screen for Digital Processing Crossover Network

(➔ page 71). Continue with the settings.

■ Powered Zone 2, Powered Zone 3

` No

` Yes:

Zone 2/3 speakers can be used. (Powered Zone 2/3

enabled).

■ 11ch Playback

` No

` Yes

For 11.2-channel playback, set this setting to “Yes”. If you

select front wide speakers setting in Speaker Configuration

is set to “None”, it will be automatically switched to

“80Hz (THX)”.

Speaker Setup

Some of the settings in this section are set automatically

by Audyssey MultEQ

XT32 Room Correction and

Speaker Setup function (➔ page 42). For Speakers B,

you need to change the settings manually.

1 2 3 4 5

“Setup”

If you change these settings, you must run

Audyssey MultEQ XT32 Room Correction and

Speaker Setup again (➔ page 42).

To be continued

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR3010 Seite 66

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR3010

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info