Bedienungsanleitung Onkyo TX-NR3010 (Seite 80 von 168) (Englisch)

492661

Zoom out

Zoom in

Vorherige Seite

1/168

Nächste Seite

Advanced Operations

En-80

■ Saturation

*1*4*6

` –50 to 0 to +50

With this setting, you can adjust saturation. “–50” is the

weakest color. “+50” is the strongest color.

■ Color Temperature

*4*6

` Warm

` Normal

` Cool

With this setting, you can adjust the color temperature.

■ Gamma

*4*6

` –3 to 0 to +3

With this setting, you can adjust the incoming picture’s R

(red), G (green), and B (blue) color signal in relation to the

output color signal.

■ Red Brightness

*4*6

` –50 to 0 to +50

With this setting you can adjust the brightness of red color.

“–50” is the darkest. “+50” is the brightest.

■ Red Contrast

*4*6

` –50 to 0 to +50

With this setting you can adjust the contrast of red color.

“–50” is the least. “+50” is the greatest.

■ Green Brightness

*4*6

` –50 to 0 to +50

With this setting you can adjust the brightness of green

color. “–50” is the darkest. “+50” is the brightest.

■ Green Contrast

*4*6

` –50 to 0 to +50

With this setting you can adjust the contrast of green color.

“–50” is the least. “+50” is the greatest.

■ Blue Brightness

*4*6

` –50 to 0 to +50

With this setting you can adjust the brightness of blue

color. “–50” is the darkest. “+50” is the brightest.

■ Blue Contrast

*4*6

` –50 to 0 to +50

With this setting you can adjust the contrast of blue color.

“–50” is the least. “+50” is the greatest.

Note

•“Picture Adjust”

cannot be used when:

–The NET input selector is selected, or

–“Monitor Out” is set to “Sub” (➔ page 63).

•“Picture Adjust” can be used when the USB input selector is

selected; however, only when iPod/iPhone is connected and

Standard Mode or Extended Mode (Video) is selected.

This procedure can also be performed on the remote controller

by using the Quick Setup (➔ page 57).

When a 3D video source is input, “Wide Mode” is fixed to

“Full”.

When “Metadata Compatible” is enabled (➔ page 70),

“Picture Mode” is fixed to “Direct”.

When the “Picture Mode” setting is set to anything other than

“Custom”, this setting cannot be used.

If the “Resolution” setting is set to “4K Upscaling”

(➔ pages 63, 79), this setting is fixed at “Off”.

Press CLR if you want to reset to the default value.

When the “Noise Reduction” setting is set to anything other

than “Off”, this setting cannot be selected.

With some TVs, there may be no picture when this setting is

set to “4K Upscaling”.

When “Resolution” is set to “1080p/24” or “4K Upscaling”

while “Monitor Out” is set to “Analog”, the video is output in

1080i.

*10

When “Resolution” is set to “Auto” while “Monitor Out” is

set to “Analog”, the video is output as “Through”.

Audio Selector

■ Audio Selector

` ARC:

The audio signal from your TV tuner can be sent to

HDMI OUT MAIN of the AV receiver.

With this selection, the TV’s audio can be

automatically selected as a priority among other

assignments.

` HDMI:

This can be selected when HDMI IN has been

assigned as an input source. If both HDMI (HDMI

IN) and digital audio inputs (COAXIAL IN or

OPTICAL IN) have been assigned, HDMI input is

automatically selected as a priority.

` COAXIAL:

This can be selected when COAXIAL IN has been

assigned as an input source. If both coaxial and

HDMI inputs have been assigned, coaxial input is

automatically selected as a priority.

` OPTICAL:

This can be selected when OPTICAL IN has been

assigned as an input source. If both optical and HDMI

inputs have been assigned, optical input is

automatically selected as a priority.

` Analog:

The AV receiver always outputs analog signals.

You can set priorities of audio output when there are both

digital and analog inputs.

Note

• This setting can be made only for an input source that is assigned

to HDMI IN, COAXIAL IN, or OPTICAL IN.

• This setting cannot be used with the NET and USB input

selectors.

• When using the Whole House Mode, this setting cannot be

selected.

• With the GAME2 input selector, “Analog” cannot be used.

You can select “ARC” if you select the TV/CD input selector.

But you cannot if you’ve selected “Off” in the “Audio Return

Channel” setting (➔ page 84).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR3010 Seite 80

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR3010

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info