492661
95
Zoom out
Zoom in
Vorherige Seite
1/168
Nächste Seite
Controlling Other Components
En-95
You’ll need to enter a code for each component that you
want to control.
Note
Though the provided remote control codes are correct at the time
of release, they are subject to change.
You can change the configuration of colored buttons, with
which REMOTE MODE buttons are preset.
Tip
To reset the REMOTE MODE buttons to their default settings,
see “Resetting the REMOTE MODE Buttons” ( page 96).
Note
If any other button than the colored buttons is pressed, the
operation will be cancelled.
This operation cannot be done while the AV receiver is in
Receiver mode or when ZONE 2/3 is active.
Entering Remote Control Codes
1
Look up the appropriate remote control code in the
separate Remote Control Codes list.
The codes are organized by category (e.g., DVD
player, TV, etc.).
2
While holding down the REMOTE MODE button to
which you want to assign a code, press and hold
down DISPLAY (about 3 seconds).
The REMOTE MODE button lights.
Note
Remote control codes cannot be entered for RECEIVER
and the multi zone button.
Only TV remote control codes can be entered for TV.
Except for RECEIVER, TV, and the multi zone button,
remote control codes from any category can be assigned for
the REMOTE MODE buttons. However, these buttons also
work as input selector buttons ( page 29), so choose a
REMOTE MODE button that corresponds with the input to
which you connect your component. For example, if you
connect your CD player to the CD input, choose TV/CD
when entering its remote control code.
3
Within 30 seconds, use the number buttons to enter
the 5-digit remote control code.
The REMOTE MODE button flashes twice.
If the remote control code is not entered successfully,
the REMOTE MODE button will flash once slowly.
Remapping Colored Buttons
1
While holding down the REMOTE MODE button
that you want to program, press and hold down A
(Red) until the REMOTE MODE button lights
(about 3 seconds).
You can only change colored buttons for components
whose codes belong to categories of the Remote
Control Codes list (BD/DVD player, TV, cable set-top
box, etc).
2
Within 30 seconds, press the colored buttons in the
order that you want to reassign them.
The button presses are assigned to each button from
left to right. The REMOTE MODE button flashes
twice, indicating that the sequence has been
successfully assigned. If the sequence is not
successfully assigned, the REMOTE MODE button
will flash once slowly.
95

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Onkyo TX-NR3010 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Onkyo TX-NR3010

Onkyo TX-NR3010 Bedienungsanleitung - Deutsch - 168 seiten

Onkyo TX-NR3010 Bedienungsanleitung - Holländisch - 168 seiten

Onkyo TX-NR3010 Bedienungsanleitung - Französisch - 168 seiten

Onkyo TX-NR3010 Bedienungsanleitung - Italienisch - 168 seiten

Onkyo TX-NR3010 Bedienungsanleitung - Spanisch - 168 seiten

Onkyo TX-NR3010 Bedienungsanleitung - Schwedisch - 168 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info