Bedienungsanleitung Onkyo TX-NR3010 (Seite 96 von 168) (Englisch)

492661

Zoom out

Zoom in

Vorherige Seite

1/168

Nächste Seite

Controlling Other Components

En-96

Onkyo components that are connected via u are

controlled by pointing the remote controller at the AV

receiver, not the component. This allows you to control

components that are out of view, in a rack, for example.

Controlling Onkyo components without u

If you want to control an Onkyo component by pointing the

remote controller directly at it, or you want to control an

Onkyo component that’s not connected via u, use the

following remote control codes:

` 30627:

Onkyo DVD player without u

` 71817:

Onkyo CD player without u

` 32900/33100/33500:

Onkyo Blu-ray Disc player

` 32901/33104/33504:

Onkyo HD DVD player

` 70868:

Onkyo MD recorder without u

` 71323:

Onkyo CD recorder without u

` 82990:

Onkyo Dock without u

You can reset a REMOTE MODE button to its default

remote control code.

You can reset the remote controller to its default settings.

By pressing the REMOTE MODE button that’s been

programmed with the remote control code for your

component, you can control your component as described

below.

For details on entering a remote control code for other

components, see “Entering Remote Control Codes”

(➔ page 95).

Controlling a TV

TV is preprogrammed with the remote control code for

controlling a TV that supports the p

(limited to

some models). The TV must be able to receive remote

control commands via p and be connected to the

AV receiver via HDMI. If controlling your TV via

p doesn’t work very well, program your TV’s

remote control code into TV and use the TV remote mode

to control your TV.

Use the following remote control codes:

` 11807/13100/13500:

TV with p

Controlling Apple TV

By programming the supplied remote controller with the

appropriate remote control code, you can use it to operate

your Apple TV.

Use the following remote control codes:

` 02615:

Apple TV

Remote Control Codes for Onkyo

Components Connected via RI

Make sure the Onkyo component is connected with

an u cable and an analog audio cable (RCA).

See “Connecting Onkyo RI Components” for details

(➔ page 25).

Enter the appropriate remote control code for a

REMOTE MODE button, by referring to the

previous section.

` 42157:

Onkyo cassette tape deck with u

` 81993:

Onkyo Dock with u

Press the REMOTE MODE button, point the

remote controller at the AV receiver, and operate

the component.

Resetting the REMOTE MODE Buttons

While holding down the REMOTE MODE button

that you want to reset, press and hold down HOME

until the REMOTE MODE button lights (about 3

seconds).

Within 30 seconds, press the REMOTE MODE

button again.

The REMOTE MODE button flashes twice,

indicating that the button has been reset.

Each REMOTE MODE button is preprogrammed

with a remote control code. When a button is reset, its

preprogrammed code is restored.

Note

• The learning command is also reset.

Resetting the Remote Controller

While holding down RECEIVER, press and hold

down HOME until RECEIVER lights (about 3

seconds).

Within 30 seconds, press RECEIVER again.

RECEIVER flashes twice, indicating that the remote

controller has been reset.

Controlling Other Components

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR3010 Seite 96

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR3010

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info