Bedienungsanleitung Onkyo TX-NR414 (Seite 50 von 128) (Englisch)

492644

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

Advanced Operations

En-50

■ Audio Return Ch (ARC)

` Off

` Auto:

The audio signal from your TV tuner can be sent to

the HDMI OUT of the AV receiver.

The audio return channel (ARC) function allows an ARC

capable TV to send the audio stream to the HDMI OUT of

the AV receiver. To use this function, you must select the

TV/CD input selector and your TV must be ARC capable.

The ARC indicator will light when the audio signal is

detected.

Note

• This setting is fixed to “----” when the “HDMI Ctrl (RIHD)”

setting is set to “Off”.

• This setting is set to “Auto” automatically when the “HDMI Ctrl

(RIHD)” setting is set to “On” for the first time.

• If you set “Audio Return Ch” to “Auto”, the “Audio Selector”

settings of the TV/CD input selector will be automatically

switched to “ARC” (➔ page 47).

■ LipSync

` Off

` On

This function allows the AV receiver to automatically

correct any delay between the video and the audio, based

on the data from the connected monitor.

Note

• This function works only if your HDMI-compatible TV supports

HDMI Lip Sync.

■ InstaPrevue

These settings apply to “InstaPrevue” of the Home menu

(➔ page 35) and specify the preview display of HDMI

video streams.

Sub Window

` Multi

Displays preview thumbnails all at once.

` Single:

Displays preview thumbnails one-by-one.

With this setting, you can set the number of preview

thumbnails displayed.

Position

(with “Sub Window” set to “Multi”)

` Top, Bottom

, Left, Right

(with “Sub Window” set to “Single”)

` UpperL, UpperR, LowerL, LowerR

With this setting, you can set the position of preview

thumbnails on the TV screen.

Menu Network Setup

This section explains how to configure the AV receiver’s

network settings manually.

If your router’s DHCP server is enabled, you don’t need to

change any of these settings, as the AV receiver is set to

use DHCP to configure itself automatically by default (i.e.,

DHCP is set to “Enable”). If, however, your router’s

DHCP server is disabled (you’re for example using static

IP), you’ll need to configure these settings yourself, in

which case, a knowledge of Ethernet networking is

essential.

What’s DHCP?

DHCP (Dynamic Host Configuration Protocol) is used by

routers, computers, the AV receiver, and other devices to

automatically configure themselves on a network.

What’s DNS?

The DNS (Domain Name System) translates domain

names into IP addresses. For example, when you enter a

domain name such as www.onkyousa.com in your Web

browser, before accessing the site, your browser uses DNS

to translate this into an IP address, in this case

63.148.251.142.

■ MAC Address

This is the AV receiver’s MAC (Media Access Control)

address. This address cannot be changed.

After changing the settings of the “HDMI Ctrl

(RIHD)”, “HDMI Through” or “Audio Return Ch”,

turn off the power on all connected pieces of equipment

and then turn them on again. Refer to the user’s manuals

for all connected pieces of equipment.

Network Setup

After modifying the network settings, you must confirm

the changes by executing “Save”.

1 2 3 4 5

“Setup”

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR414 Seite 50

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR414

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info