Bedienungsanleitung Onkyo TX-NR414 (Seite 48 von 128) (Englisch)

492644

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

Advanced Operations

En-48

Setting the Incoming Digital Signal (Fixed

Mode)

■ Fixed Mode

` Off

The format is detected automatically. If no digital

input signal is present, the corresponding analog

input is used instead.

` PCM:

Only 2-channel PCM format input signals will be

heard. If the input signal is not PCM, the PCM

indicator will flash and noise may also be produced.

` DTS:

Only DTS (but not DTS-HD) format input signals

will be heard. If the input signal is not DTS, the dts

indicator will flash and there will be no sound.

When “HDMI”, “COAXIAL” or “OPTICAL” is selected

in the “Audio Selector” setting, you can then specify the

signal type in “Fixed Mode”.

Normally, the AV receiver detects the signal format

automatically. However, if you experience either of the

following issues when playing PCM or DTS material, you

can manually set the signal format to PCM or DTS.

• If the beginnings of tracks from a PCM source are cut off,

try setting the format to PCM.

• If noise is produced when fast forwarding or reversing a

DTS CD, try setting the format to DTS.

Note

• The setting will be reset to “Off” when you change the setting in

“Audio Selector” (➔ page 47).

Menu Hardware

OSD

■ Volume OSD

` On

` Off

Turn this setting on to display the volume level on the TV

screen while it is adjusted.

Remote ID

■ Remote ID

` 1

, 2, or 3

When several Onkyo components are used in the same

room, their remote ID codes may overlap. To differentiate

the AV receiver from other components, you can change

its remote ID from “1”, to “2” or “3”.

Note

• If you do change the AV receiver’s remote ID, be sure to change

the remote controller to the same ID (see below), otherwise, you

won’t be able to control it with the remote controller.

Changing the remote controller’s ID

Tuner

■ AM/FM Freq Step (North American and

Taiwanese models)

` 10kHz/200kHz

` 9kHz/50kHz:

Select the frequency step according to your area.

■ AM Freq Step (European, Australian and Asian

models)

` 10kHz:

` 9kHz

Select the frequency step according to your area.

For AM/FM tuning to work properly, you must specify the

AM/FM frequency step used in your area.

Note

• When this setting is changed, all radio presets will be deleted.

Auto Standby

■ Auto Standby

` Off

` On

When “Auto Standby” is set to “On”, the ASb indicator

lights and the AV receiver will automatically enter standby

mode if there is no operation for 30 minutes with no audio

and no video signal input.

“Auto Standby” will appear on the AV receiver’s display

and OSD 30 seconds before the Auto Standby comes on.

Default setting: On (European, Australian and Asian

models), Off (North American and Taiwanese models)

Note

•Set to “

On”, the Auto Standby function may activate itself during

playback with some sources.

•The Auto

Standby function does not work when Zone 2 is on.

Hardware

While holding down RECEIVER, press and hold

down Q SETUP until the remote indicator lights

(about 3 seconds).

Use the number buttons to enter ID 1, 2, or 3.

The remote indicator flashes twice.

1 2 3 4 5

“Setup”

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR414 Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR414

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info