Bedienungsanleitung Onkyo TX-NR5008 (Seite 103 von 116) (Englisch)

553766

103

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

103

■ Stand-by power consumption

■ The sound changes when I connect my

headphones

■ The speaker distance cannot be set as required

■ The display doesn’t work

■ How do I change the language of a multiplex

source

■ The u functions don’t work

■ The functions System On/Auto Power On and

Direct Change don’t work for components

connected via u

■ When performing “Audyssey MultEQ

XT32

Room Correction and Speaker Setup”, the

measurement fails showing the message

“Ambient noise is too high.”.

■ The following settings can be made for the

S-Video and composite video inputs

You must use the buttons on the unit to make these set-

tings.

1. While holding down the input selector button for the input

source that you want to set, press SETUP.

2. Use e/r to change the setting.

3. Press the input selector button for the input source that you

want to set when you’ve finished.

• Video Attenuation

This setting can be made for the BD/DVD, VCR/DVR,

CBL/SAT, GAME, or AUX input.

If you have a games console connected to the composite

video input, and the picture isn’t very clear, you can

attenuate the gain.

Video ATT:OFF: (default).

Video ATT:ON: Gain reduced by 2dB.

Others

In the following cases, the power consumption may

reach up to a maximum of 30W:

1. You are using the Universal Port jack.

2. “Control” is set to “Enable” in the “Network”

setting.

3. “HDMI Control(RIHD)” setting is set to

“On”. (Depending on the TV status, the AV

receiver will enter Standby mode as usual.)

65, 76,

When a pair of headphones is connected, the listen-

ing mode is set to Stereo, unless it’s already set to

Stereo, Mono, Direct, or Pure Audio.

—

In some cases, corrected values suitable for home

theater use may be set automatically.

—

The display is turned off when the Pure Audio listen-

ing mode is selected.

—

Use the “Multiplex” setting on the “Audio Adjust”

menu to select “Main” or “Sub”.

To use u, you must make an u connection and an

analog audio connection (RCA) between the compo-

nent and AV receiver, even if they are connected dig-

itally.

While Zone 2 or Zone 3 is selected, the u func-

tions don’t work.

—

While Zone 2 or Zone 3 is selected, the u func-

tions don’t work.

—

This can be caused by any malfunction in your

speaker unit. Check if the unit produces normal

sounds.

—

The AV receiver contains a microcomputer for signal

processing and control functions. In very rare situations,

severe interference, noise from an external source, or

static electricity may cause it to lockup. In the unlikely

event that this happens, unplug the power cord from the

wall outlet, wait at least five seconds, and then plug it

back in again.

Onkyo is not responsible for damages (such as CD

rental fees) due to unsuccessful recordings caused by

the unit’s malfunction. Before you record important

data, make sure that the material will be recorded cor-

rectly.

Before disconnecting the power cord from the wall out-

let, set the AV receiver to Standby.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR5008 Seite 103

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR5008

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info