Bedienungsanleitung Onkyo TX-NR535 (Seite 8 von 20) (Englisch)

548134

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Step 2:

Setting Up

When the measurement is completed, the

measurement result is displayed.

AccuEQ Room Calibration

<-Review Speaker Configuration->

Subwoofer : Yes

Front : Small

Center : Small

Surround : Small

Crossover : 150 Hz

Save

Cancel

Press

on the remote controller to check the settings.

Pressing ENTER when "Save" is selected will save the

settings.

• The subwoofer sound may not be detected since

it is extremely low frequencies. If "No" is shown for

"Subwoofer" in the measurement result screen,

raise the subwoofer volume to around the half of

its maximum volume and make its frequency to the

maximum level.

On the screen showing "AccuEQ" is "On", press

ENTER.

The settings will be applied to all the inputs.

When "Please unplug setup microphone." is

displayed, disconnect the microphone.

•

If you change the speaker positions, the room furniture

layout or the number of speakers, perform automatic

speaker setting again.

• If there is an error message, follow the on-screen

instruction to remove the error cause.

Making Wi-Fi setting

Items to be checked before starting the procedure

Wi-Fi connection requires an access point such as

wireless LAN router (



). Write down the SSID and

password (key) of the access point if they are shown

in the label of the main body. If the access point has

an automatic setting button (may be called differently

according to the manufacturer), you can set up

without inputting the password. For how to use the

automatic setting button of the access point, refer to

its instruction manual.



The unit supports Wi-Fi connection with 2.4 GHz

access point.



Operation: You can set up by viewing the guidance

displayed on the TV screen. To display the guidance, you

need to make HDMI connection between the unit and

TV. Select the item with the cursor buttons of the remote

controller and press ENTER to confirm your selection. To

return to the previous screen, press RETURN.

Start "Wi-Fi Setup".

Press RCV on the remote controller and then press

HOME.

Select "Setup" with the cursor buttons and press

ENTER.

Select "12. Network Setup" with the cursor buttons and

press ENTER.

• "12. Network Setup" becomes selectable after the

network starts up even if it cannot be selected first. It

may take about a minute to start up.

Select "Wi-Fi" with the cursor buttons and select "On" to

display "Wi-Fi Setup".

Select "Start" in "Wi-Fi Setup" with the cursor buttons

and press ENTER.

Select the SSID of the access point to be connected

with the cursor buttons and press ENTER.

When the SSID of the access point appears on the TV

screen, select the desired access point.

• If you changed the initial setting of the access point to

skip password entry, step 4 starts automatically.

• If you changed the initial setting of the access point

to hide the SSID, see "When the access point is not

displayed".

Select and set the authentication method.

Wi-Fi Setup

Please select the authentic

method.

Enter Password

Push Button

PIN code

When the screen above is displayed, select and set one of

the three authentication methods: "Enter Password", "Push

Button" and "PIN code". See below for details of and how to

set each method.



Enter Password: Enter the password of the access point

to establish connection.

Select "Enter Password" with the cursor buttons and

press ENTER.

Enter the password (



) on the keyboard screen, select

"OK" with the cursor buttons and press ENTER.

• In some case, the key board screen is displayed

automatically instead of authentication screen

depending on access point device.



To switch uppercase/lowercase, select "Shift" and press ENTER.

Select "Left" or "Right" and press ENTER to move the cursor to

the selected direction. Select "BS" and press ENTER to delete

the character at the left of the cursor position. To select whether to

mask the password with "*" or display it in plain text, press D on the

remote control. Press + 10 on the remote controller to enable the

"Shift" function and CLR to delete all the input characters.

If the security method of the access point to be

connected is WEP, select "Default Key ID", select "OK"

and press ENTER.



Push Button: Use the automatic setting button of the

access point to establish connection.

Select "Push Button" with the cursor buttons and press

ENTER.

Hold down the automatic setting button of the access

point for the necessary seconds, select "OK" with the

cursor buttons and press ENTER.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR535 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR535

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info