Bedienungsanleitung Onkyo TX-NR801 (Seite 9 von 97) (Englisch)

553769

Zoom out

Zoom in

Vorherige Seite

1/97

Nächste Seite

Index Parts and Facilities

—Continued

For further operational instructions, see the pages indi-

cated in brackets [ ].

POWER switch (for all models other than

USA, Canadian and Australian models) [27]

Press to turn on and off the main power supply for

the TX-NR801/TX-NR801E. When the TX-NR801/

TX-NR801E is turned on with the POWER switch,

the STANDBY indicator lights.

• Before turning on the power, check to make sure

that all cords are properly connected.

• When the power is turned on, a sudden surge of cur-

rent will occur that may adversely affect the opera-

tion of other devices. To prevent this, do not plug the

TX-NR801/TX-NR801E into the same circuit used

by sensitive equipment, e.g., computers.

STANDBY/ON button [27]

If pressed with the POWER switch turned on (with

the receiver plugged in for USA, Canadian and Aus-

tralian models), the TX-NR801/TX-NR801E turns

on and the display lights up. If pressed again, the

TX-NR801/TX-NR801E returns to the standby state.

In the standby state, the display is turned off and the

TX-NR801/TX-NR801E cannot be operated.

STANDBY indicator [7, 27]

Lights when the TX-NR801/TX-NR801E is in the

standby state and when a signal is received from the

remote controller.

AUDIO SELECTOR button [41, 65]

Press to select the type of audio input signal.

DIRECT/PURE AUDIO button [41, 39, 65]

Press to switch between the direct and pure audio

listening modes.

Remote control sensor [7]

DISPLAY button [41]

Press to display information about the current input

source signal. Each time you press the DISPLAY

button, the screen changes to show you different

information concerning the input signal.

DIMMER button (Other than European

models) [40]

Press to set the brightness of the front display. There are

three settings available: normal, dark, and very dark.

The brightness of the front display can also be

changed using the remote controller.

RT/PTY/TP button (European models only) [49]

This button is only available on European models.

Press this button to tune into the Radio Data System

(RDS) for FM broadcasting. RDS was developed

within the European Broadcasting Union (EBU)

and is available in most European countries. Each

time the button is pressed, the display changes from

RT (radio text) to PTY (program type) to TP (trafﬁc

program) and then back to RT again.

STEREO button [44]

Selects for the stereo listening mode.

SURROUND button [44]

Selects for the Dolby Pro Logic II, DTS Neo:6,

Dolby Digital, or DTS listening modes.

THX button [44]

Selects for the THX listening mode.

DSP / buttons [44]

Switches to the DSP (Digital Signal Processing) modes.

Front display

MEMORY button [47]

Press to assign the radio station to which you are

currently tuned to a preset channel or press to delete

a previously preset station.

FM MODE button [46]

Press to change the stereo mode from AUTO to

MONO and vice versa. Each time this button is

pressed, the AUTO indication turns on and off indicat-

ing the current mode. If you are listening to an FM

radio station in stereo and the sound cuts out or there is

a great deal of noise, switch from AUTO to MONO.

TUNING / , PRESET / buttons [46,

47, 49]

To tune into a radio station, press the TUNING

buttons. The tuner frequency is displayed in the

front display and it can be changed in 100-kHz (or

50-kHz) increments for FM and 10-kHz (or 9-kHz)

increments for AM.

When FM is selected as the input source, you can hold

down either the TUNING or button and then

release it to activate the auto-search feature. It will

search for a station in the direction of the button you

pressed and stop when it tunes into one. When navigat-

ing through the menu settings, these buttons move the

cursor up or down (or change the highlighted item).

To select a radio station that was stored using the

MEMORY button, press the PRESET / buttons.

When navigating through the menu settings, these

buttons select the value or item that you selected

with the TUNING

buttons.

When you press the SETUP button, the TUNING

and PRESET buttons become cursor buttons to be

used for Setup Menu operations.

REC OUT/ZONE 2/OFF buttons [50-51, 68]

These buttons allow you to use the TX-NR801/

TX-NR801E to output to a remote zone (Zone 2) or

to another component for recording (Rec Out). Press

the REC OUT button to output the audio and video

signals to a recording component for recording. Press

the ZONE 2 button to enjoy the output from the

TX-NR801/TX-NR801E in a different room, which is

referred to as the remote zone (Zone 2).

When either button is pressed, the currently selected

input source for recording or outputting to the remote

zone is displayed in the front panel display. If

“SOURCE” is displayed, then the same input source

as that selected for the main zone will be output.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR801 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info