Bedienungsanleitung Onkyo TX-NR801 (Seite 87 von 97) (Englisch)

553769

Zoom out

Zoom in

Vorherige Seite

1/97

Nächste Seite

Letting the Remote Controller Learn the Codes from Other Remote

Controllers—Continued

Notes:

• The remote controller codes for Onkyo compact disc

players, cassette tape decks, DVD players, and mini

disc recorder have already been programmed into

buttons on the remote controller. You may, however,

use these buttons to program the codes for other

remote controllers. If you wish to restore the Onkyo

preset codes after you program new codes, you must

ﬁrst erase the new codes (See this page).

• The remote controller has 408 memory slots (8

modes × 51 buttons). Some remote controllers may

have more commands than can be remembered by the

remote controller. In such cases, it will be necessary

for you to determine which commands are more

important to you.

• If the SEND/LEARN indicator quickly ﬂashes three

times and turns off, then the remote controller has

exited the programming mode because either you

have made a mistake during programming or a time-

out has occurred because no button was pressed.

Resume from Step 2.

• If you try to program beyond the learning capacity of

the remote controller, the SEND/LEARN indicator

ﬂashes six times quickly, and the remote controller

exits the programming mode. Try programming

under a different MODE button.

• When you want to program a command to a button to

which you have already programmed a command, sim-

ply follow the same procedure given and the previous

programming for that button will be overwritten.

• The remote controller uses infrared rays to send its

commands, as do most other remote controllers.

Though most remote controller codes can be memo-

rized by the remote controller, be aware that some

remote controllers use systems that are quite different

from the remote controller and therefore may not be

able to be programmed.

• Some remote controllers have a single button that

performs multiple functions (for example, the func-

tion may change each time the button is pressed). If

this is the case, each function must be programmed to

a separate button on the remote controller.

• Once you have transferred the commands from the

other remote controller, refer to the instruction man-

ual that came with that product for instructions on

how to operate that product.

• Make sure both the remote controller and the other

remote controller have new batteries. If either of them

has batteries that are low, you may not be able to pro-

gram the commands of the other remote controller

properly into the remote controller.

Erasing the programmed command from one

button

You can only erase memorized commands and not preset ones.

Note:

If no button is pressed for more than 30 seconds during

the erasing procedure, the SEND/LEARN indicator

ﬂashes three times quickly, and the remote controller

exits the erasing mode. Resume from Step 1.

Erasing all the commands programmed under a

MODE button

Notes:

• If no button is pressed for more than 30 seconds dur-

ing the erasing procedure, the SEND/LEARN indica-

tor ﬂashes three times quickly and the remote

controller exits the erasing mode. Resume from Step 1.

• If you perform an invalid operation during erasing,

the SEND/LEARN indicator ﬂashes three times

quickly, and the remote controller exits the erasing

mode. Resume from Step 1.

• If many commands have been programmed to the

MODE button, then the SEND/LEARN indicator

may remain lit for up to 20 seconds during Step 2.

This is not a malfunction.

Press and hold down the MODE button for

the command, press the ENTER/ZONE 2

button, and then release both buttons.

When you press the MODE button, the SEND/

LEARN indicator lights. When you press the

ENTER/ZONE 2 button, the lamp turns off. When

you release the buttons, the lamp lights again.

Press and release the button for the com-

mand you wish to erase.

When you press the button, the SEND/LEARN

indicator turns off. When you release the button,

the lamp lights again.

Press and release the same button again.

The SEND/LEARN lamp slowly ﬂashes twice.

The memorized command is erased.

Press and hold down the desired MODE

button, press the ENTER/ZONE 2 button

twice, and then release both buttons.

When you press the MODE button, the SEND/

LEARN indicator lights. When you press the

ENTER/ZONE 2 button, the lamp turns off.

When you release the buttons, the lamp slowly

ﬂashes twice and then lights again.

Press and release the same MODE button

again.

When you release the button, the SEND/LEARN

indicator slowly ﬂashes twice. This erases all the

commands memorized to the MODE button.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR801 Seite 87

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info