Bedienungsanleitung Onkyo TX-NR801 (Seite 88 von 97) (Englisch)

553769

Zoom out

Zoom in

Vorherige Seite

1/97

Nächste Seite

Using the Macro Function

What is the macro function?

A macro function enables you to program a series of

button operations (up to 16) on the remote controller

into a single button. The series of operations are then

called a macro. For example, to play a compact disc

player connected to the TX-NR801/TX-NR801E nor-

mally, you must perform the following steps:

1. Press the RCVR MODE button.

2. Press the ON button.

3. Press the CD (INPUT SELECTOR) button.

4. Press the CD MODE button.

5. Press the playback ( ) button.

By using the macro function, you can perform the above

ﬁve operations by only pressing one button.

Tips:

• If you erase or change the command of a button pro-

grammed in the macro, that operation of that button

will no longer work in the macro. In this case, it will

be necessary for you to reprogram the macro in order

to avoid incorrect operation.

• The codes programmed into the macro will be trans-

mitted at an interval of 0.5 seconds. However, some

devices may not be able to complete one operation in

0.5 seconds and may miss the next code. In this case,

after pressing one operation button, you can press the

same MODE button again before pressing the next

operation button to add another 0.5 seconds between

the two operations.

With the macro function, you can program a series of

button operations as a macro into the MACRO button so

the macro can be executed with just one touch. Note

that for the macro function, only two macros can be

programmed. For example, to program the macro

described above on this page for the MACRO button,

perform the steps given below.

Notes:

• You may program up to 16 button operations into the

macro function. If you try to program a 17th opera-

tion, it will be ignored, and programming is stopped.

• If the SEND/LEARN indicator quickly ﬂashes three

times and turns off, then the remote controller has

exited the programming mode because either you

have made a mistake during programming or a time-

out has occurred because no button was pressed.

Resume from Step 1.

MACRO 2

MACRO 1

CD MODE

RCVR MODE

MODE buttons

SEND/LEARN

indicator

(CD playback)

(INPUT

SELECTOR)

Programming the Macro

Press and hold down any one of the 8

MODE buttons, press the MACRO 1 (or 2)

button, and then release both buttons.

When you press the MODE button, it lights and

the SEND/LEARN indicator lights. When you

press the MACRO 1 (or 2) button, the indicator

turns off. When you release the buttons, the indi-

cator ﬂashes brieﬂy and then lights again.

Press the operation buttons you wish to

program in order (in this case, press

RCVR MODE → ON → CD (INPUT SELEC-

TOR) → CD MODE → playback ( ) but-

ton).

When you press each button, the SEND/LEARN

indicator turns off. When you release the button,

the indicator lights.

Press the MACRO 1 (or 2) button to com-

plete the procedure.

The SEND/LEARN indicator slowly ﬂashes

twice.

Check to see if the macro has been prop-

erly programmed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR801 Seite 88

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info