Bedienungsanleitung Onkyo TX-NR808 (Seite 58 von 100) (Englisch)

645307

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

■ Receiver

` via NET:

You can update the firmware via Internet. Check the

network connection before update.

` via USB:

You can update the firmware from a USB mass stor-

age device.

You can update the AV receiver’s firmware. Do not shut-

down the power of the AV receiver while update.

■ Universal Port

` via NET:

You can update the firmware via Internet. Check the

network connection before update.

` via USB:

You can update the firmware from a USB mass stor-

age device.

You can update the Onkyo dock’s firmware. Do not shut-

down the power of the AV receiver while update.

Note

• This update shall not be performed when no dock is connected

to UNIVERSAL PORT jack.

With this preference, you can protect your settings by

locking the setup menus.

Main menu Lock Setup

■ Setup

` Locked:

Setup menus locked.

` Unlocked

Setup menus not locked.

When the setup menus are locked, you cannot change any

setting.

You can change various audio settings from the Home

menu (➔ 26).

Note

• These settings are disabled when:

– a pair of headphones is connected, or

–the “Audio TV Out” setting is set to “On” (➔ 56) and an

input selector other than HDMI is selected.

Tone Control Settings

You can adjust the bass and treble for the front speakers,

except when the Direct, Pure Audio or THX listening

mode is selected.

■ Bass

` –10dB to 0dB

to +10dB in 2 dB steps.

You can boost or cut low-frequency sounds output

by the front speakers.

■ Treble

` –10dB to 0dB

to +10dB in 2 dB steps.

You can boost or cut high-frequency sounds output

by the front speakers.

Operating on the AV receiver

Note

• This setting is not available when the multichannel Analog input

is selected.

Speaker Levels

You can adjust the volume of each speaker while listening

to an input source.

These temporary adjustments are cancelled when the AV

receiver is set to Standby. To save the setting you made

here, go to “Level Calibration” (➔ 47) before setting the

AV receiver to Standby.

■ Subwoofer Level

` –15.0dB to 0.0dB

to +12.0dB in 1 dB steps.

■ Center Level

` –12.0dB to 0.0dB to +12.0dB in 1 dB steps.

Note

• You cannot use this function while the AV receiver is muted.

• Speakers that are set to “No” or “None” in the

“Speaker Configuration” (➔ 46) cannot be adjusted.

Audyssey Settings

■ Dynamic EQ

See “Dynamic EQ” of “Source Setup” (➔ 50).

■ Dynamic Volume

See “Dynamic Volume” of “Source Setup” (➔ 51).

Lock Setup

Using the Audio Settings

Press RECEIVER followed by HOME.

Useq/w to select “Audio”, and then use q/w/e/r

to make the desired selection.

Press TONE on the AV receiver repeatedly to

select either “Bass” or “Treble”.

Use Up r and Down e on the AV receiver to

adjust.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR808 Seite 58

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR808

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info