Bedienungsanleitung Onkyo TX-NR808 (Seite 81 von 100) (Englisch)

645307

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

When you have a network connection, select

the brand name again, and then press ENTER.

When you do NOT have a network connection,

use q/w to select the brand name, and then

press ENTER.

The following screen appears.

The AV receiver accesses and searches the

database. Select “Search by model number( via

network )”, and then press ENTER. When you

do NOT have a network connection, select

“Skip” when you don’t want to select the

model, and then press ENTER.

If you select “Skip”, you will go to step 11.

Enter the model in a similar manner as in the

case of the brand name (step 6).

Tip

• After entering the 3rd character, press ENTER to start

searching.

• You cannot enter a space character.

Use q/w to select the model, and then press

ENTER.

If the brand name is not found, use r to select

“Not Listed”, and then press

ENTER.

After searching is completed, a message for

remote control code transfer will appear.

While pointing the remote controller at the AV

receiver’s remote control sensor, press ENTER.

8–1. Remote Mode Setup

Skip

Search by model number( via network )

Category

Brand

Model

Sonic

(Option)

8–1. Remote Mode Setup

Now we are ready to transfer data to remote.

Please hold remote so that it is facing the receiver.

Ready?

Category

Brand

Model

XXXXX

xxxxx[***/***]

Approx.

16ft. (5 m)

Incoming sensor

Remote control sensor (Transmitter)

15° off center

(Left/Right/Up/Down)

When you have a network connection, a mes-

sage “Successful” will appear. Now the transfer

is successful!

You’ll return to the category selection menu.

Press SETUP to end the remote mode setup.

When you do NOT have a network connection,

the following screen appears.

Push any key (except for arrow buttons and

ENTER) to see if the component responds.

When category other than TV have been selected,

the content is different.

If you can control component, press

RECEIVER, use q/w to select “Works”, and

then press ENTER.

If you cannot control component, use q/w to

select “Doesn’t work (Try next code)” and

press ENTER.

The next code appears.

Press ENTER to transfer the determined code.

Press ENTER.

You’ll return to the category selection menu.

Press SETUP to end the remote mode setup.

8–1. Remote Mode Setup

Works

Doesn’t work (Try next code)

1. Push some key to see if the TV responds.

(except Arrow and Enter.)

2. Choose “Works” or “Doesn’t work”.

Category

Brand

Code

XXXXX

xxxxx[***/***]

8–1. Remote Mode Setup

Now we are ready to transfer data to the remote.

Please hold the remote so that it is facing the receiver.

Use ENTER button of your remote to activate “OK”.

Ready?

Category

Brand

Code

XXXXX

xxxxx[***/***]

Approx.

16ft. (5 m)

Incoming sensor

Remote control sensor (Transmitter)

15° off center

(Left/Right/Up/Down)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR808 Seite 81

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR808

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info