Bedienungsanleitung Onkyo TX-NR808 (Seite 82 von 100) (Englisch)

645307

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

You’ll need to enter a code for each component that you

want to control.

Note

• The remote control codes provided are correct at the time of

printing, but are subject to change.

Onkyo components that are connected via u are con-

trolled by pointing the remote controller at the AV

receiver, not the component. This allows you to control

components that are out of view, in a rack, for example.

If you want to control an Onkyo component by pointing

the remote controller directly at it, or you want to control

an Onkyo component that’s not connected via u, use the

following remote control codes:

• BD/DVD

` 30627

Onkyo DVD player without u

• TV/CD

` 71817

Onkyo CD player without u

` 11807:

TV with p

If you want to control an Onkyo component by pointing the

remote controller directly at it, use the following remote

control codes:

` 32900

Onkyo Blu-ray Disc player

` 32901:

Onkyo HD-DVD player

` 70868:

Onkyo MD recorder without u

` 71323:

Onkyo CD recorder without u

` 82990:

Onkyo Dock without u

Note

• If you connect a cassette tape deck to the TV/CD IN jack, or

connect an RI Dock to the to the TV/CD IN or VCR/DVR IN or

GAME IN jacks, for u to work properly, you must set the Input

Display accordingly (➔ 27).

Entering Remote Control Codes

Look up the appropriate remote control code in

the separate Remote Control Codes list.

The codes are organized by category (e.g., DVD

player, TV, etc.).

While holding down REMOTE MODE to which

you want to enter a code, press and hold down

DISPLAY (about 3 seconds).

The REMOTE MODE button lights.

Note

• Remote control codes cannot be entered for RECEIVER

and ZONE.

• Only TV remote control codes can be entered for TV.

• Except for RECEIVER, TV and ZONE, remote control

codes from any category can be entered as REMOTE

MODE. However, these buttons also work as input selec-

tor buttons (➔ 25), so choose a REMOTE MODE that

corresponds with the input to which you connect your

component. For example, if you connect your CD player

to the CD input, choose TV/CD when entering its remote

control code.

Within 30 seconds, use the number buttons to

enter the 5-digit remote control code.

REMOTE MODE button flashes twice.

If the remote control code is not entered success-

fully, REMOTE MODE button will flash once

slowly.

Remote Control Codes for Onkyo

Components Connected via u

Make sure the Onkyo component is connected

with an u cable and an analog audio cable

(RCA).

See “Connecting Onkyo u Components” for details

(➔ 20).

Enter the appropriate remote control code for

REMOTE MODE.

• BD/DVD

` 31612:

Onkyo DVD player with u

• TV/CD

` 71327:

Onkyo CD player with u

` 42157:

Onkyo cassette tape deck with u

• PORT

` 81993:

Onkyo Dock with u

See the previous section for how to enter remote

control codes.

Note

• When using a cassette tape deck connected via u, press

and hold TV/CD to switch to TAPE.

Press REMOTE MODE, point the remote control-

ler at the AV receiver, and operate the component.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR808 Seite 82

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR808

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info