Bedienungsanleitung Onkyo TX-NR808 (Seite 89 von 100) (Englisch)

645307

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

■ Only the center speaker produces sound

■ The surround speakers produce no sound

■ The center speaker produces no sound

■ The front high, front wide and surround back

speakers produce no sound

■ The subwoofer produces no sound

■ There’s no sound with a certain signal format

■ Can’t select the Pure Audio listening mode

■ Can’t get 6.1/7.1 playback

■ The speaker volume cannot be set as required

(The volume cannot be set to 100.0(MAX))

■ Noise can be heard

■ The Late Night function doesn’t work

■ About DTS signals

■ The beginning of audio received by an HDMI IN

can’t be heard

If you use the Dolby Pro Logic IIx Movie, Dolby Pro

Logic IIx Music, or Dolby Pro Logic IIx Game lis-

tening mode with a mono source, such as an AM

radio station or mono TV program, the sound is con-

centrated in the center speaker.

—

In the Mono listening mode, only the front speakers

output sound if the “Output Speaker” setting is set

to “Center”.

Make sure the speakers are configured correctly. 46

When the T-D (Theater-Dimensional), Stereo or

Mono listening mode is selected, the surround

speakers produce no sound.

—

Depending on the source and current listening mode,

not much sound may be produced by the surround

speakers. Try selecting another listening mode.

—

Make sure the speakers are configured correctly. 46

When the Stereo or Mono listening mode is selected,

the center speaker produces no sound.

—

In the Mono listening mode, only the front speakers

output sound if the “Output Speaker” setting is set

to “Left / Right”.

Make sure the speakers are configured correctly. 46

Depending on the current listening mode, no sound

may be produced by the front high, front wide and

surround back speakers. Select another listening

mode.

Not much sound may be produced by the front high,

front wide and surround back speakers with some

sources.

—

Make sure the speakers are configured correctly. 46

While Powered Zone 2 is being used, playback in the

main room is reduced to 5.1-channels and the front

high, front wide and surround back speakers produce

no sound.

When you play source material that contains no

information in the LFE channel, the subwoofer pro-

duces no sound.

—

Make sure the speakers are configured correctly. 46

Check the digital audio output setting on the con-

nected device. On some game consoles, such as

those that support DVD, the default setting is off.

—

With some DVD-Video discs, you need to select an

audio output format from a menu.

—

Depending on the input signal, some listening modes

cannot be selected.

36–40

The Pure Audio listening mode cannot be selected

while Zone 2/3 is on.

—

If no surround back speakers, front wide and front

high speakers are connected, or the Zone 2 speakers

are being used, 6.1/7.1 playback is not possible.

—

You can not always select all of the listening modes,

depending on the number of the speakers connected.

36–40

Check to see if a maximum volume has been set. 55

If the volume level of each individual speaker has

been adjusted to high positive values, then the maxi-

mum master volume possible may be reduced. Note

that the individual speaker volume levels are set

automatically after Audyssey MultEQ

Room Cor-

rection and Speaker Setup function has been com-

pleted.

28, 46

Using cable ties to bundle audio cables with power

cords, speaker cables, and so on may degrade the

audio performance, so don’t do it.

—

An audio cable may be picking up interference. Try

repositioning your cables.

—

Make sure the source material is Dolby Digital,

Dolby Digital Plus, and Dolby TrueHD.

When DTS program material ends and the DTS bit-

stream stops, the AV receiver remains in DTS listen-

ing mode and the DTS indicator remains on. This is

to prevent noise when you use the pause, fast for-

ward, or fast reverse function on your player. If you

switch your player from DTS to PCM, because the

AV receiver does not switch formats immediately,

you may not hear any sound, in which case you

should stop your player for about three seconds, and

then resume playback.

—

With some CD and LD players, you won’t be able to

playback DTS material properly even though your

player is connected to a digital input on the AV

receiver. This is usually because the DTS bitstream

has been processed (e.g., output level, sampling rate,

or frequency response changed) and the AV receiver

doesn’t recognize it as a genuine DTS signal. In such

cases, you may hear noise.

—

When playing DTS program material, using the

pause, fast forward, or fast reverse function on your

player may produce a short audible noise. This is not

a malfunction.

—

Since it takes longer to identify the format of an

HDMI signal than it does for other digital audio sig-

nals, audio output may not start immediately.

—

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR808 Seite 89

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR808

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info