Bedienungsanleitung Onkyo TX-NR828 (Seite 93 von 152) (Englisch)

527521

Zoom out

Zoom in

Vorherige Seite

1/152

Nächste Seite

Appendix

En-93

■ The beginning of audio received by an HDMI IN

can’t be heard

■ There’s no sound during Whole House Mode

■ There’s no picture

■ There’s no picture from a source connected to

an HDMI IN

■ The on-screen menus don’t appear

■ The on-screen information does not appear

■ Reception is noisy, FM stereo reception is noisy,

or the FM STEREO indicator doesn’t light

■ The remote controller doesn’t work

■ Can’t control other components

Since it takes longer to identify the format of an HDMI

signal than it does for other digital audio signals, audio

output may not start immediately.

Make sure you’ve selected an analog audio input.

Video

Make sure that all video connecting plugs are pushed in all

the way. (➔ page 21)

Make sure that each video component is properly

connected. (➔ page 18)

If your TV is connected to the HDMI output(s), select

“-----” in the “HDMI Input” setting to watch composite

video, and component video sources. (➔ page 62)

If the video source is connected to a component video

input, you must assign that input to an input selector, and

your TV must be connected to either the HDMI output(s) or

COMPONENT VIDEO OUT. (➔ pages 18, 63)

If the video source is connected to a composite video input,

your TV must be connected to the HDMI output(s) or the

corresponding composite video output. (➔ page 18)

If the video source is connected to an HDMI input, you

must assign that input to an input selector, and your TV

must be connected to the HDMI output(s). (➔ pages 18,

62)

While the Pure Audio listening mode is selected, the

analog video circuitry is turned off and only video signals

input through HDMI IN can be output. (➔ page 44)

On your TV, make sure that the video input to which the AV

receiver is connected is selected.

When the “Monitor Out” setting is set to “Both”, the “HDMI

Through” setting is only available for the HDMI OUT MAIN

jack. (➔ pages 61, 75)

Reliable operation with an HDMI-to-DVI adapter is not

guaranteed. In addition, video signals from a PC are not

guaranteed. (➔ page 102)

When the resolution is set to any resolution not supported

by the TV, no video is output from the HDMI outputs.

(➔ page 61)

If the message “Resolution Error” appears on the AV

receiver’s display, this indicates that your TV does not

support the current video resolution and you need to select

another resolution on your DVD player.

On your TV, make sure that the video input to which the AV

receiver is connected is selected.

When the AV receiver is not connected to a TV via HDMI

OUT MAIN, on-screen menus are not displayed.

Depending on the input signal, the on-screen information

may not appear when the input signal from HDMI IN is

output to a device connected to the HDMI output.

Tuner

Relocate your antenna.

Move the AV receiver away from your TV or computer.

Listen to the station in mono. (➔ page 41)

When listening to an AM station, operating the remote

controller may cause noise.

Passing cars and airplanes can cause interference.

Concrete walls weaken radio signals.

If nothing improves the reception, install an outdoor

antenna.

Remote Controller

Before operating this unit, be sure to press RECEIVER.

Make sure that the batteries are installed with the correct

polarity. (➔ page 13)

Install new batteries. Don’t mix different types of batteries,

or old and new batteries. (➔ page 13)

Make sure that the remote controller is not too far away

from the AV receiver, and that there’s no obstruction

between the remote controller and the AV receiver’s

remote control sensor. (➔ page 13)

Make sure that the AV receiver is not subjected to direct

sunshine or inverter-type fluorescent lights. Relocate if

necessary.

If the AV receiver is installed in a rack or cabinet with

colored-glass doors, the remote controller may not work

reliably when the doors are closed.

Make sure you’ve selected the correct remote controller

mode. (➔ pages 12, 84)

When using the remote controller to control other

manufacturers’ AV components, some buttons may not

work as expected.

Make sure you’ve entered the correct remote control code.

(➔ page 82)

Make sure to set the same ID on both the AV receiver and

remote controller. (➔ page 78)

If it’s an Onkyo component, make sure that the u cable

and analog audio cable are connected properly.

Connecting only an u cable won’t be enough.

(➔ page 23)

Make sure you’ve selected the correct remote controller

mode. (➔ pages 12, 84)

If you’ve connected an cassette tape deck to the TV/CD IN

jack, or an RI Dock to the TV/CD IN or GAME 1 IN jacks,

for the remote controller to work properly, you must set the

input display appropriately. (➔ page 53)

If you cannot operate it, you will need to enter the

appropriate remote control code. (➔ page 82)

To control another manufacturer’s component, point the

remote controller at that component. (➔ page 82)

To control an Onkyo component that’s connected via u,

point the remote controller at the AV receiver. Be sure to

enter the appropriate remote control code first.

(➔ page 83)

To control an Onkyo component that’s not connected via

u, point the remote controller at the component. Be sure

to enter the appropriate remote control code first.

(➔ page 83)

Onkyo TX-NR828 Seite 93

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR828

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info