Bedienungsanleitung Onkyo TX-NR905 (Seite 132 von 136) (Englisch)

64580

132

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

132

Troubleshooting

—Continued

• Check the Speaker Conﬁguration (page 94).

• While Powered Zone 2 is being used, playback in the

main room is reduced to 5.1-channels and the sur-

round back speakers produce no sound (page 119).

The subwoofer produces no sound

• If the source material contains no audio in the LFE

channel, the subwoofer produces no sound.

• Check the Speaker Conﬁguration (page 94).

The Zone 2/3 speakers produce no sound

• The Zone 2/3 speakers only output sources that are

connected to an analog input. Check to see if the

source component is connected to an analog input.

•Powered Zone 2 cannot be used if Speaker Type Front

A is set to Bi-Amp or BTL, or Speaker Type Front B

is set to Normal, Bi-Amp, or BTL (page 51).

There’s no sound with a certain signal format

• Check the digital audio output setting on the source

component. On some game consoles, such as those

that can play DVDs, the default setting is off.

•With some DVD-Video discs, you need to select an

audio format from a menu or with the AUDIO button

on your DVD player’s remote controller.

Can’t get 6.1- or 7.1-channel playback

• While Powered Zone 2 is being used, playback in the

main room is reduced to 5.1-channels and the sur-

round back speakers produce no sound (page 119).

Can’t select the Pure Audio listening mode

• The Pure Audio listening mode cannot be selected

while Zone 2 is on.

The volume cannot be set to +18 dB (99)

• Check to see if a maximum volume has been set

(page 106).

• After the Automatic Speaker Setup function has been

run, or the volume level of each individual speaker has

been adjusted (pages 76 and 99), the maximum vol-

ume may be reduced.

Noise can be heard

• Using cable ties to bundle audio cables with power

cords, speaker cables, and so on can degrade audio

performance, so don’t use them.

• An audio cable may be picking up interference. Try

repositioning your cables.

The Late Night function doesn’t work

• Make sure that the source is Dolby Digital (page 89).

The analog multichannel input doesn’t work

• Check the multichannel input connections (page 38).

• Make sure that the multichannel input is assigned to

the input selector (page 60).

• Make sure that the multichannel input is selected

(page 78).

• Check the audio output settings on your DVD player.

About DTS signals

• When playing DTS program material, using the pause,

fast forward, or fast reverse function on your player

may produce a short audible noise. This is not a mal-

function.

• When DTS program material ends and the DTS bit-

stream stops, the AV receiver remains in DTS listen-

ing mode and the DTS indicator remains on. This is to

prevent noise when you use the pause, fast forward, or

fast reverse function on your player. If you switch your

player from DTS to PCM, as the AV receiver does not

switch formats immediately, you may not hear any-

thing, in which case you should stop your player for

about 3 seconds, and then resume playback.

•With some CD players, you won’t be able to playback

DTS material properly even though your player is con-

nected to a digital input on the AV receiver. This is

usually because the DTS bitstream has been processed

(e.g., output level, sampling rate, or frequency

response changed) and the AV receiver doesn’t recog-

nize it as a genuine DTS signal. In such cases, you

may hear noise.

The beginning of audio received by an HDMI IN

can’t be heard

• Since it takes longer to identify the format of an

HDMI signal than it does for other digital audio sig-

nals, sound may not be output immediately.

There’s no picture

• Make sure that all video connecting plugs are pushed

in all the way (page 33).

• Make sure that each video component is properly con-

nected.

• On your TV, make sure that the video input to which

the AV receiver is connected is selected.

• While the Pure Audio listening mode is selected, the

video circuitry is turned off and only the HDMI OUT

outputs video signals.

• If your TV is connected to the HDMI output, set the

HDMI Monitor setting to Main or Sub (page 52), and

select “- - -” in the “HDMI Input Setup” on page 54 to

watch composite video, S-Video, and component

video sources.

• If your TV is connected to the COMPONENT VIDEO

OUT, set the HDMI Monitor setting to No (page 52),

and select “- - -” in the “Component Video Input

Setup” on page 56 to watch composite video and

S-Video sources.

• If the video source is connected to a component video

input, your TV must be connected to the COMPO-

NENT VIDEO OUT or HDMI OUT (page 34).

• If the video source is connected to an HDMI input,

your TV must be connected to the HDMI OUT

(page 34).

Video

TX-NR905_En.book Page 132 Monday, June 18, 2007 12:55 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR905 Seite 132

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR905

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info