Bedienungsanleitung Onkyo TX-NR906 (Seite 66 von 150) (Englisch)

62439

Zoom out

Zoom in

Vorherige Seite

1/150

Nächste Seite

First Time Setup—Continued

The onscreen menus shown in this manual may be

slightly different from what you see on your TV.

Turn on the AV receiver and the

connected TV.

On the TV, select the input to which the

AV receiver is connected.

Place the speaker setup micro-

phone at measurement point 1

(page 64), and connect it to the

SETUP MIC jack.

Notes:

•

Before starting Audyssey MultEQ

Automatic Speaker Setup, arrange

the room and connect the speakers as

you would for enjoying movies.

Changes to the room after auto setup

requires you run the auto setup again,

as room EQ characteristics may have

changed.

• When starting the automatic speaker

setup, do not stand between the

speakers and microphone, and avoid

obstacles blocking the path between

speakers and microphone. This will

produce inaccurate results.

• Position the microphone at ear height

of a seated listener with the micro-

phone tip pointed directly at the ceil-

ing using a tripod. Do not hold the

microphone in your hand during

measurements as this will produce

innacurate results.

• Make the room as quiet as possible.

Background noise can disrupt the

room measurements. Close win-

dows, silence cell phones, televi-

sions, radios, air conditioners,

fluorescent lights, home appliances,

light dimmers, or other devices.

• Cell phones should be turned off or

placed away from all audio electron-

ics during the measurement process

as Radio Frequency Interference

(RFI) may cause measurement dis-

ruptions (even if the cell phone is not

in use).

Auto Speaker Setup

Please place microphone at center of listening area at

ear height.

ENTER

Press [ENTER].

The automatic speaker setup starts.

Test tones are played through each

speaker as Audyssey MultEQ

Automatic Speaker Setup runs. This

process takes a few minutes. Please

refrain from talking during

measurements and do not stand

between speakers and the microphone.

The speaker detect results

appear.

“Yes” means that the speaker was

detected. “No” means that no speaker

was detected.

If you agree with the results, use

the Up and Down [q]/[w] buttons

to select “Next”, and then press

[ENTER].

The options are:

Next: Proceed to the next step.

Retry: Return to step 2 and try again.

Cancel: Cancel the automatic speaker

setup.

The following screen appears.

Place the setup microphone at

the next position (see page 65),

and then press [ENTER].

Audyssey MultEQ

XT performs more

measurements. This takes a few minutes.

Auto Speaker Setup

Do not unplug Setup Mic.

Please keep quiet.

Now measuring. . .

Auto Speaker Setup

Speaker Detect Result

Retry

Cancel

:Yes :No

ENTER

MOVE

Auto Speaker Setup

Please place microphone at next position at ear height.

ENTER

Auto Speaker Setup

Do not unplug Setup Mic.

Please keep quiet.

Now measuring. . .

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR906 Seite 66

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR906

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info