Bedienungsanleitung Onkyo TX-NR906 (Seite 100 von 150) (Englisch)

62439

100

Zoom out

Zoom in

Vorherige Seite

1/150

Nächste Seite

100

Advanced Setup—Continued

Note:

This procedure can also be performed on the AV receiver

by using its [SETUP] button, arrow buttons, and

[ENTER] button.

Speaker Level Calibration

With the “Level Calibration” settings, you can adjust the

level of each speaker while listening to the test tone so

that the volume of each speaker is the same at the listen-

ing position. You can adjust the levels of front Speakers

A and front Speakers B independently. The other speak-

ers (i.e., subwoofer, center, surround, and surround back)

use the same level settings for Speakers A and Speakers

Notes:

• The speakers cannot be calibrated while the output of

the AV receiver is muted.

• The test tone is output at the standard level for THX,

which is 0 dB (absolute volume setting 82). If you nor-

mally listen at volume settings below this, be careful

because the test tone will be much louder.

Use the Up and Down [q]/[w] but-

tons to select a speaker, and use

the Left and Right [e]/[r] but-

tons to specify the distance.

Specify the distance from the speaker

to your listening position.

Notes:

• You can specify different distances

for front Speakers A and front

Speakers B, but not the other speak-

ers (i.e., subwoofer, center, surround,

and surround back).

• The “Center” distance cannot be set

if the “Center” is set to “None”

(page 95) or “Not Use” (page 98).

• The “SurrRight” and “SurrLeft” dis-

tances cannot be set if the “Sur-

round” is set to “None” (page 95) or

“Not Use” (page 98).

• The “SurrBack R” and “SurrBack L”

distances cannot be set if “Speaker

Type: Front(Speaker A) or

Front(Speaker B)” is set to

“Bi-Amp” or “BTL” (page 61),

“SurrBack” is set to “None”

(page 95) or “Not Use” (page 98), or

“Powered Zone2” is being used

(page 132).

• The “Subwoofer” distance cannot be

set if “Subwoofer” is set to “No”

(page 96).

Repeat step 7 for each speaker.

Press the [SETUP] button.

Setup closes.

Press the [RECEIVER] REMOTE

MODE button, and then use the

remote controller’s [SP A] or

[SP B] button to select Speakers

A or Speakers B, respectively

(TX-NR906 only).

Notes:

• Speakers B cannot be selected if

“Speaker Type: Front(Speaker B)” is

set to “Not Use”.

• TX-SR876 continue with step 2 after

press the [RECEIVER] REMOTE

MODE button.

Press the [SETUP] button.

The main menu appears onscreen.

These settings are set automatically by the Automatic

Speaker Setup function (see page 64).

LISTENING MODE

DISPLAY MUTING

DIMMER

CDR/MD/DOCK

SAT

TAPE/AMP

SLEEP

REMOTE MODE

SUBTITLE

AUDIO

REPEAT

PLAY MODE

PLAYLIST

RANDOMREC

ENTER

SURR

DIRECT

THX

PURE A

STEREO

ALL ST

VOL

DISC

ALBUM

VCR

CABLE

NET/USB

DVD

RECEIVER

ZONE

SP A SP B

2, 7

3-6

*TX-NR906 only

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR906 Seite 100

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR906

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info