Bedienungsanleitung Onkyo TX-NR906 (Seite 129 von 150) (Englisch)

62439

129

Zoom out

Zoom in

Vorherige Seite

1/150

Nächste Seite

129

NET/USB (TX-NR906 only)—Continued

Note:

This procedure can also be performed on the AV receiver

by using its [SETUP] button, arrow buttons, and

[ENTER] button.

Mac Address

This is the AV receiver’s MAC (Media Access Control)

address. This address cannot be changed.

Control

This setting enables or disables control over the network.

Enable: Control over the network enabled.

Disable: Control over the network disabled.

■ Port

This is the network port used for control over the net-

work.

DHCP

This setting determines whether or not the AV receiver

uses DHCP to automatically configure its IP Address,

Subnet Mask, Gateway, and DNS Server settings.

Enable: DHCP enabled.

Disable: DHCP disabled.

If you select “Disable”, you must configure the “IP

Address”, “Subnet Mask”, “Gateway”, and “DNS

Server” settings yourself.

IP Address

If you set the “DHCP” setting to “Disable”, you must

specify an IP address. Enter a static IP address provided

by your ISP.

The IP address must be within the following ranges.

Class A: 10.0.0.0 to 10.255.255.255

Class B: 172.16.0.0 to 172.31.255.255

Class C: 192.168.0.0 to 192.168.255.255

Most routers use Class C IP addresses.

Subnet Mask

If you set the “DHCP” setting to “Disable”, you must

specify a subnet mask address.

Enter the subnet mask address provided by your ISP

(typically: 255.255.255.0).

Gateway

If you set the “DHCP” setting to “Disable”, you must

specify a gateway address.

Enter the gateway address provided by your ISP.

DNS Server

If you set the “DHCP” setting to “Disable”, you must

specify a DNS server.

Enter the DNS server addresses provided by your ISP.

Proxy URL

To use a Web proxy, enter its URL here.

Proxy Port

If you’re using a Web proxy, enter a proxy port number

here.

Use the Up and Down [q]/[w] but-

tons to select “6. Network”, and

then press [ENTER].

The “Network” screen appears.

Use the Up and Down [q]/[w] but-

tons to select the settings, and

use the Left and Right [e]/[r]

buttons to set them.

To enter an IP address, select the set-

ting, and then press [ENTER]. The

arrow [q]/[w]/[e]/[r] buttons can

then be used to enter numbers. Press

[ENTER] again to set the number.

The settings are explained on the next

page.

When you’ve finished, press the

Up and Down [q]/[w] buttons to

select “ Save Settings”, and

then press [ENTER].

Setup closes.

When modifying network settings,

after modifying it is necessary to exe-

cute “ Save Settings”.

When you’ve finished, press the

[SETUP] button.

Setup closes.

7-6. Network

MAC Address

Control

Port

xx : xx : xx : xx : xx : xx

Enable

xxxxx

MOVE VALUE INPUT RETURN

ENTER

RETURN

EXIT

SETUP

7-6. Network

Proxy

Proxy URL

Proxy Port

Save Settings

Disable

8080

MOVE VALUE ENTER RETURN

ENTER

RETURN

EXIT

SETUP

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR906 Seite 129

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR906

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info