Bedienungsanleitung Onkyo TX-NR929 (Seite 81 von 160) (Englisch)

517568

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

Advanced Operations

En-81

Operating

procedure

(➔ page 61)

■ MAC Address

This is the AV receiver’s MAC (Media Access

Control) address. This address cannot be changed.

■ DHCP

` Enable

` Disable

This setting determines whether or not the AV

receiver uses DHCP to automatically configure its IP

Address, Subnet Mask, Gateway, and DNS Server

settings.

Note

• If you select “Disable”, you must configure the “IP

Address”, “Subnet Mask”, “Gateway”, and “DNS Server”

settings yourself.

■ IP Address

` Class A:

“10.0.0.0” to “10.255.255.255”

` Class B:

“172.16.0.0” to “172.31.255.255”

` Class C:

“192.168.0.0” to “192.168.255.255”

Enter a static IP address provided by your Internet

Service Provider (ISP).

Most routers use Class C IP addresses.

■ Subnet Mask

Enter the subnet mask address provided by your ISP

(typically 255.255.255.0).

■ Gateway

Enter the gateway address provided by your ISP.

■ DNS Server

Enter the DNS server address provided by your ISP.

■ Proxy URL

To use a Web proxy, enter its URL here.

■ Proxy Port

If you’re using a Web proxy, enter a proxy port

number here.

■ Network Standby

` On

` Off

This setting enables or disables control over the

network.

When enabled, the NET indicator will be dimly-lit

while the AV receiver is in standby mode. Note that

the indicator may not light under certain conditions

(➔ page 26).

Note

• When set to “On”, the power consumption slightly

increases in standby mode.

■ Update Notice

` Enable

` Disable

When this setting is enabled, you will be notified if a

firmware update via network of high importance is

available.

Note

• Selecting “Never Remind me” on the notification window

will switch this setting to “Disable” (➔ page 26).

• For details on the update notification, see “Firmware

Update Notification” (➔ page 26).

■ Bluetooth

This setting enables the AV receiver to pair with

Bluetooth-enabled device.

Status

Press ENTER button to display “Now Pairing” and

start pairing.

Tip

• If pairing setting is not set, “Ready” appears on-screen

display. The name of the device paired with the AV receiver

is displayed if pairing setting is set.

• For details on the Bluetooth connection, refer to the

instruction manual of the Bluetooth-enabled device.

• The pairing can be done by holding down BLUETOOTH

button on the AV receiver until BLUETOOTH indicator

flashes.

Note

• This setting cannot be selected if you’ve selected NET or

USB as input selector in Multi Zone.

Initial Setup

If you skipped the initial setup wizard, for example on

first-time use, you can reaccess it from here.

See “Initial Setup” (➔ page 26).

Note

• This setting cannot be selected if the “Monitor Out” setting

is set to “Sub”.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR929 Seite 81

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR929

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info