Bedienungsanleitung Onkyo TX-NR929 (Seite 97 von 160) (Englisch)

517568

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

Appendix

En-97

■ Only the front speakers produce sound

■ Only the center speaker produces sound

■ The surround speakers produce no sound

■ The center speaker produces no sound

■ The front high, front wide and surround back

speakers produce no sound

■ The subwoofer produces no sound

■ There’s no sound with a certain signal format

■ Can’t select the Pure Audio listening mode

■ Can’t get 6.1/7.1 playback

■ The speaker volume cannot be set as required

■ Noise can be heard

■ The Late Night function doesn’t work

■ About DTS signals

If the input signal format is set to “PCM” or “DTS”. Set it to

“Off”. (➔ page 76)

When the Stereo or Mono listening mode is selected, only

the front speakers and subwoofer produce sound.

(➔ page 47)

In the Mono listening mode, only the front speakers output

sound if the “Output Speaker” setting is set to “Left /

Right”. (➔ page 69)

Make sure the speakers are configured correctly.

(➔ page 65)

If you use the Dolby Pro Logic IIx Movie, Dolby Pro Logic

IIx Music, or Dolby Pro Logic IIx Game listening mode with

a mono source, such as an AM radio station or mono TV

program, the sound is concentrated in the center speaker.

In the Mono listening mode, only the center speaker output

sound if the “Output Speaker” setting is set to “Center”.

(➔ page 69)

Make sure the speakers are configured correctly.

(➔ page 65)

When the T-D (Theater-Dimensional), Stereo or Mono

listening mode is selected, the surround speakers produce

no sound.

Depending on the source and current listening mode, not

much sound may be produced by the surround speakers.

Try selecting another listening mode. (➔ page 45)

Make sure the speakers are configured correctly.

(➔ page 65)

When the Stereo or Mono listening mode is selected, the

center speaker produces no sound.

In the Mono listening mode, only the front speakers output

sound if the “Output Speaker” setting is set to “Left /

Right”. (➔ page 69)

Make sure the speakers are configured correctly.

(➔ page 65)

Depending on the current listening mode, no sound may be

produced by the front high, front wide and surround back

speakers. Select another listening mode. (➔ page 45)

Depending on the sources, the sound produced by the

front high, front wide and surround back speakers may be

weak.

Make sure the speakers are configured correctly.

(➔ page 65)

When Powered Zone 2 is used, playback in the main room

is reduced to 7.1 channels and the front wide speakers

produce no sound.

When Powered Zone 3 is used, playback in the main room

is reduced to 5.1 channels and the front high, front wide

and surround back speakers produce no sound.

When you play source material that contains no information

in the LFE channel, the subwoofer produces no sound.

Make sure the speakers are configured correctly.

(➔ page 65)

Check the digital audio output setting on the connected

device. On some game consoles, such as those that

support DVD, the default setting is off.

With some DVD-Video discs, you need to select an audio

output format from a menu.

Depending on the input signal, some listening modes

cannot be selected. (➔ pages 45 to 52)

The Pure Audio listening mode cannot be selected while

Zone 2/3 is on.

If no surround back speakers, front wide speakers and

front high speakers are connected, or the Zone 3 speakers

are being used, 6.1/7.1 playback is not possible.

Depending on the number of connected speakers, it is not

always possible to select all of the listening modes.

(➔ pages 45 to 52)

Check to see if a maximum volume has been set.

(➔ page 77)

If the volume level of each individual speaker has been

adjusted to high positive values, then the maximum master

volume possible may be reduced. Note that the individual

speaker volume levels are set automatically after the

Audyssey MultEQ

XT32 Room Correction and Speaker

Setup has been performed. (➔ pages 28, 66, 67)

Using cable ties to bundle audio cables with power cords,

speaker cables, and the like may degrade the audio

performance, so refrain from doing it.

An audio cable may be picking up interference. Try

repositioning your cables.

Make sure the source material is Dolby Digital, Dolby

Digital Plus, and Dolby TrueHD. (➔ page 59)

Make sure that the “TrueHD Loudness Management”

setting is not set to “Off”. The Late Night function doesn’t

work when this setting is disabled. (➔ page 70)

When DTS program material ends and the DTS bitstream

stops, the AV receiver remains in DTS listening mode and

the dts indicator remains on. This is to prevent noise when

you use the pause, fast forward, or fast reverse function on

your player. If you switch your player from DTS to PCM,

you may not hear any sound because the AV receiver does

not switch formats immediately. In such case, you should

stop your player for about three seconds and then resume

playback.

With some CD and LD players, you won’t be able to

playback DTS material properly even though your player is

connected to a digital input on the AV receiver. This is

usually because the DTS bitstream has been processed

(e.g., output level, sampling rate, or frequency response

changed) and the AV receiver doesn’t recognize it as a

genuine DTS signal. In such cases, you may hear noise.

Playing DTS program material, using the pause, fast

forward, or fast reverse function on your player may

produce a short audible noise. This is not a malfunction.

Onkyo TX-NR929 Seite 97

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR929

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info