Bedienungsanleitung Onkyo TX-NR929 (Seite 99 von 160) (Englisch)

517568

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

Appendix

En-99

■ Can’t learn commands from another remote

controller

■ There’s no sound

■ There’s no video

■ The AV receiver’s remote controller doesn’t

control my iPod/iPhone

■ The AV receiver unexpectedly selects my

iPod/iPhone as the input source

■ iPod/iPhone doesn’t work properly

■ There’s no sound

■ The Zone 2/3 speakers produce no sound

■ Cannot access to Wi-Fi (Wireless LAN) network

or Sound playback is interrupted and

communication doesn’t work

■ Music playback is unavailable on the AV

receiver even after successful Bluetooth

connection

■ The audio quality is poor after connection with a

Bluetooth-enabled device

To control an Onkyo component that’s not connected via

u, point the remote controller at the component. Be sure

to enter the appropriate remote control code first.

(➔ page 88)

The entered remote control code may not be correct. If

more than one code is listed, try each one.

When learning commands, make sure that the transmitting

ends of both remote controllers are pointing at each other.

(➔ page 94)

Are you trying to learn from a remote controller that cannot

be used for learning? Some commands cannot be learned,

especially those that contain several instructions.

RI Dock for iPod/iPhone

Make sure your iPod/iPhone is actually playing.

Make sure your iPod/iPhone is properly inserted in the

Dock.

Make sure the AV receiver is turned on, the correct input

source is selected, and the volume is turned up.

Make sure the plugs are pushed in all the way.

Try resetting your iPod/iPhone.

Make sure that your iPod/iPhone model’s TV OUT setting

is set to On.

Make sure the correct input is selected on your TV or the

AV receiver.

Some versions of the iPod/iPhone do not output video.

Make sure your iPod/iPhone is properly inserted in the

Dock. If your iPod/iPhone is in a case, it may not connect

properly to the Dock. Always remove your iPod/iPhone

from the case before inserting it into the Dock.

The iPod/iPhone cannot be operated while it’s displaying

the Apple logo.

Make sure you’ve selected the right remote mode.

(➔ page 93)

When you use the AV receiver’s remote controller, point it

toward your AV receiver.

If you still can’t control your iPod/iPhone, start playback by

pressing your iPod/iPhone model’s Play button. Remote

operation should then be possible.

Try resetting your iPod/iPhone.

Depending on your iPod/iPhone, some buttons may not

work as expected.

Always pause iPod/iPhone playback before selecting a

different input source. If playback is not paused, the Direct

Change function may select your iPod/iPhone as the input

source by mistake during the transition between tracks.

Try reconnecting your iPod/iPhone.

Zone 2/3

Audio can be output only when analog, NET, USB or HDMI

(2ch PCM) input source is selected in Zone 2.

Audio can be output only when analog, NET or USB input

source is selected in Zone 3.

To use the Zone 2 speakers, you must set the “Powered

Zone 2” setting to “Yes”. (➔ page 65)

To use the Zone 3 speakers, you must set the “Powered

Zone 3” setting to “Yes”. (➔ page 65)

Wi-Fi (Wireless LAN) Network

The setting of SSID and encryption (WEP, etc.) is not

correct. Make the same settings for network and the AV

receiver.

Cannot receive radio wave due to a bad connection.

Shorten the distance from wireless LAN access point or

remove obstacles for a good visibility, and try again. Place

the AV receiver away from microwave ovens or other

access points.

2.4 GHz band for wireless LAN may not be enough.

Connect the ETHERNET port and router with the Ethernet

cable after selecting “Wired” in “Network Connection”

setting in “Network”. (➔ pages 20, 80)

Place the AV receiver away from the devices emitting

electromagnetic waves on the 2.4 GHz band (microwave

ovens, game consoles, etc.). If this does not solve the

problem, stop using other devices which emit

electromagnetic waves.

When other wireless LAN devices are used near the AV

receiver, several issues such as interrupted playback and

communication may occur. You can avoid these issues by

changing the channel of your Wi-Fi router. For instructions

on changing channels, see the instruction manual provided

with your Wi-Fi router.

If there is a metallic object near the AV receiver, wireless

LAN connection may not be possible as the metal can

effect on the radio wave.

If there is more than one access point in the network,

separate each access point.

It is recommended to place the Wi-Fi router (access point)

and the AV receiver in the same room.

Bluetooth

Depending on the characteristics or specifications of your

Bluetooth-enabled device, playback on the AV receiver is

not guaranteed.

The Bluetooth reception is poor. Move the Bluetooth-

enabled device closer to the AV receiver or remove any

obstacle between the Bluetooth-enabled device and the AV

receiver.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR929 Seite 99

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR929

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info