Bedienungsanleitung Onkyo TX-NR929 (Seite 100 von 160) (Englisch)

517568

100

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

Appendix

En-100

■ Cannot connect with the AV receiver

■ Bluetooth connection cannot be built

■ Can’t access the server or Internet radio

■ Playback stops while listening to music files on

the server

■ Can’t connect to the AV receiver from a Web

browser

■ Can’t access the music files on a USB device

■ Standby power consumption

■ The sound changes when I connect my

headphones

■ The speaker distance cannot be set as required

■ The display doesn’t work

■ How do I change the language of a multiplex

source

■ The u functions don’t work

■ The functions System On/Auto Power On and

Direct Change don’t work for components

connected via u

■ When performing Automatic Speaker Setup, the

measurement fails and the message “Ambient

noise is too high.” is displayed.

The Bluetooth-enabled device does not support the profiles

required for the AV receiver.

The Bluetooth function of the Bluetooth-enabled device is

not enabled. Refer to the instruction manual of the

Bluetooth-enabled device for how to enable the function.

When building a Bluetooth connection between the AV

receiver and your Bluetooth-enabled device for the first

time, if the connection is fail, you need to power off your

Bluetooth-enabled device and power on again to clear the

device name, and build the connection again.

If there is metallic object near the AV receiver, Bluetooth

connection may not be possible as the metal can effect on

the radio wave.

If the wireless LAN and Bluetooth connections are used at

the same time, try to connect the ETHERNET port and

router with the Ethernet cable after selecting “Wired” in

“Network Connection” setting in “Network” for a better

connection. (➔ pages 20, 80)

Music Server and Internet Radio

Certain network service or contents available through this

device may not be accessible in case the service provider

terminates its service.

Check the network connection between the AV receiver

and your router or switch. (➔ page 20)

Make sure that your modem and router are properly

connected, and make sure they are both turned on.

Make sure the server is up and running and compatible

with the AV receiver. (➔ page 108)

Check the “Network”settings. (➔ page 80)

Make sure your server is compatible with the AV receiver.

(➔ page 108)

If you download or copy large files on your computer,

playback may be interrupted. Try closing any unused

programs, use a more powerful computer, or use a

dedicated server.

If the server is serving large music files to several

networked devices simultaneously, the network may

become overloaded and playback may be interrupted.

Reduce the number of playback devices on the network,

upgrade your network, or use a switch instead of a hub.

If you’re using DHCP, your router may not always allocate

the same IP address to the AV receiver, so if you find that

you can’t connect to a server or Internet radio station,

recheck the AV receiver’s IP address on the “Network”

screen. (➔ page 80)

Check the “Network” settings. (➔ page 80)

USB Device Playback

Make sure the USB device is plugged in properly.

The AV receiver supports USB devices that support the

USB mass storage device class. However, playback may

not be possible with some USB devices even if they

conform to the USB mass storage device class.

(➔ page 108)

Depending on the type of format, the playback from a USB

device may not be performed normally. Check the type of

the file formats that is supported. (➔ page 109)

USB memory devices with security functions cannot be

played.

Others

In the following cases, the power consumption in standby

mode may reach up to a maximum of 9.0 W:

– The “HDMI CEC (RIHD)” setting is set to “On”.

(Depending on the TV status, the AV receiver will enter

standby mode as usual.)

– The “HDMI Through” setting is set to other than “Off”.

– The “Network Standby” setting is set to “On”.

(➔ pages 78, 81)

If an MHL-enabled mobile device connected to the AUX

(front) input is charged, the power consumption in standby

mode will increase than the figure above. (➔ page 20)

When a pair of headphones is connected, the listening

mode is set to Stereo, unless it’s already set to Stereo,

Mono, Direct, or Pure Audio.

The values entered may be automatically adjusted with

values best-suited for your home theater.

The display is turned off when the Pure Audio listening

mode is selected.

Use the “Multiplex” setting in the “Audio Adjust” menu to

select “Main” or “Sub”. (➔ page 69)

To use u, you must make an u connection and an

analog audio connection (RCA) between the component

and AV receiver, even if they are connected digitally.

(➔ page 24)

While Zone 2/3 is selected, the u functions don’t work.

(➔ page 24)

These functions don’t work when Zone 2/3 is turned on.

(➔ page 24)

This can be caused by a malfunction in your speaker unit.

Check if the unit produces normal sounds.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR929 Seite 100

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR929

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info