Bedienungsanleitung Onkyo TX-SR605 (Seite 96 von 100) (Englisch)

62549

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

Troubleshooting—Continued

• If the video source is connected to a component video

input, your TV must be connected to the COMPO-

NENT VIDEO OUT or HDMI OUT (page 25).

• If the video source is connected to an HDMI input,

your TV must be connected to the HDMI OUT

(page 25).

• While the Pure Audio listening mode (not North

American models) is selected, the video circuitry is

turned off and only video signals input through HDMI

IN can be output.

• On your TV, make sure that the video input to which

the AV receiver/AV amplifier is connected is selected.

There’s no picture from a source connected to

an HDMI IN

• If the message “Resolution Error” appears on the AV

receiver/AV amplifier’s display, this indicates that the

TV or display does not support the current video reso-

lution and you need to select another resolution on

your DVD player.

The onscreen menus don’t appear

• The onscreen menus may do not appear on a TV that’s

connected to the HDMI OUT. When the HDMI Mon-

itor Out is set to No (page 47), the onscreen menus are

output at a resolution of 480i. If the onscreen menus

do not appear, set the HDMI Monitor Out to Yes

(page 47).

• Make sure that the video settings are correct (page 48).

• On your TV, make sure that the video input to which

the AV receiver/AV amplifier is connected is selected.

The immediate display does not appear

• The immediate display appears on a device connected

to the COMPONENT VIDEO OUT, when the Com-

ponent Video Setup (page 49) is set to “---.”

• If both of the HDMI Video Setup (page 48) and the

Component Video Setup (page 49) are set to “---,” the

immediate display is output to a device connected to

the HDMI OUT.

Reception is noisy, FM stereo reception is

noisy, or the FM STEREO indicator doesn’t

appear

• Relocate your antenna.

• Move the AV receiver away from your TV or com-

puter.

• Listen to the station in mono (page 57).

• When listening to an AM station, operating the remote

controller may cause noise.

• Passing cars and airplanes can cause interference.

• Concrete walls weaken radio signals.

• If nothing improves the reception, install an outdoor

antenna.

The remote controller doesn’t work

• Make sure that the batteries are installed with the cor-

rect polarity (page 12).

• Install new batteries. Don’t mix different types of bat-

teries, or old and new batteries (page 12).

• Make sure that the remote controller is not too far

away from the AV receiver/AV amplifier, and that

there’s no obstruction between the remote controller

and the AV receiver/AV amplifier’s remote control

sensor (page 12).

• Make sure that the AV receiver/AV amplifier is not

subjected to direct sunshine or inverter-type fluores-

cent lights. Relocate if necessary.

• If the AV receiver/AV amplifier is installed in a rack

or cabinet with colored-glass doors, the remote con-

troller may not work reliably when the doors are

closed.

• Make sure you’ve selected the correct remote control-

ler mode (pages 13-16).

• When using the remote controller to control other

manufacturers’ AV components, some buttons may

not work as expected.

• Make sure you’ve entered the correct remote control

code.

• Make sure to set the same ID on both the AV receiver/

AV amplifier and remote controller (pages 83 and 86).

Can’t control other components

• If it’s an Onkyo component, make sure that the

cable and analog audio cable are connected properly.

Connecting only an cable won’t work (page 39).

• Make sure you’ve selected the correct remote control-

ler mode (pages 13-16).

• If you’ve connected an -capable Onkyo MD

recorder, CD recorder, Dock to the TAPE IN/

OUT jacks, or an Dock to the GAME/TV IN

jacks, for the remote controller to work properly, you

must set the display to MD, CDR, or DOCK (pages 51

and 91).

• To control another manufacturer’s component, point

the remote controller at that component.

• To control an Onkyo component that’s connected via

, point the remote controller at the AV receiver/AV

amplifier. Be sure to enter the appropriate remote con-

trol code first (page 91).

• To control an Onkyo component that’s not connected

via , or another manufacturer’s component, point

the remote controller at the component. Be sure to enter

the appropriate remote control code first (page 90).

Tuner (TX-SR605 only)

Remote Controller

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-SR605 Seite 96

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-SR605

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info