Bedienungsanleitung Onkyo TX-SR806 (Seite 117 von 124) (Englisch)

63833

117

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

117

Troubleshooting

If you have any trouble using the AV receiver/AV ampli-

fier, look for a solution in this section. If you can’t

resolve the issue yourself, contact your Onkyo dealer.

Can’t turn on the AV receiver/AV amplifier

• Make sure that the power cord is properly plugged into

the wall outlet.

• Unplug the power cord from the wall outlet, wait five

seconds or more, then plug it in again.

The AV receiver/AV amplifier turns off as soon

as it’s turned on

•

The amp protection circuit has been activated. Remove

the power cord from the wall outlet immediately. Discon-

nect all speaker cables and input sources, and leave the

AV receiver/AV amplifier with its power cord discon-

nected for 1 hour. After that, reconnect the power cord

and set the volume to maximum. If the AV receiver/AV

amplifier stays on, set the volume to minimum, discon-

nect the power cord, and reconnect your speakers and

input sources. If the AV receiver/AV amplifier turns off

when you set the volume to maximum, disconnect the

power cord, and contact your Onkyo dealer.

There’s no sound, or it’s very quiet

• Make sure that the digital input source is selected

properly (page 46).

• Make sure that all audio connecting plugs are pushed

in all the way (page 22).

• Make sure that the inputs and outputs of all compo-

nents are connected properly (page 25-38).

• Make sure that the polarity of the speaker cables is

correct, and that the bare wires are in contact with the

metal part of each speaker terminal (page 18).

• Make sure that the input source is properly selected

(page 56).

• Make sure that the speaker cables are not shorting.

• Check the volume. It can be set to

−∞ dB, −81.5 dB

through +18.0 dB (page 56). The AV receiver/AV

amplifier is designed for home theater enjoyment. It

has a wide volume range, allowing precise adjustment.

•

While a pair of headphones is connected to the PHONES

jack, no sound is output by the speakers (page 58).

• If there’s no sound from a DVD player connected to an

HDMI IN, check the DVD player’s output settings,

and be sure to select a supported audio format.

• Check the digital audio output setting on the con-

nected device. On some game consoles, such as those

that support DVD, the default setting is off.

• With some DVD-Video discs, you need to select an

audio output format from a menu.

• If your turntable uses an MC cartridge, you must con-

nect an MC head amp, or an MC transformer.

• Make sure that none of the connecting cables are bent,

twisted, or damaged.

• Not all listening modes use all speakers (page 71).

• Specify the speaker distances (page 78) and adjust the

individual speaker levels (page 79).

• Make sure that the speaker setup microphone is not

still connected.

• The input signal format is set to PCM or DTS. Set it to

Auto (page 98).

Only the front speakers produce sound

• When the Stereo listening mode is selected, only the

front speakers and subwoofer produce sound.

• In the Mono listening mode, only the front speakers

output sound if the “Output Speaker” setting is set to

“Left / Right” (page 83).

• Check the Speaker Configuration (page 75).

Only the center speaker produces sound

• If you use the Dolby Pro Logic IIx Movie, Dolby Pro

Logic IIx Music, or Dolby Pro Logic IIx Game listen-

ing mode with a mono source, such as an AM radio

station or mono TV program, the sound is concen-

trated in the center speaker.

• In the Mono listening mode, only the front speakers

output sound if the “Output Speaker” setting is set to

“Center” (page 83).

•

Make sure the speakers are configured correctly (page 75).

The surround speakers produce no sound

• When the Stereo or Mono listening mode is selected,

the surround speakers produce no sound.

• Depending on the source and current listening mode,

not much sound may be produced by the surround

speakers. Try selecting another listening mode.

• Make sure the speakers are configured correctly

(page 75).

Power

Audio

If you can’t resolve the issue yourself, try resetting

the AV receiver/AV amplifier before contacting your

Onkyo dealer.

To reset the AV receiver/AV amplifier to its factory

defaults, turn it on and, while holding down the

[VCR/DVR] button, press the [ON/STANDBY] but-

ton. “Clear” will appear on the display and the AV

receiver/AV amplifier will enter Standby mode.

Note that resetting the AV receiver/AV amplifier will

delete your radio presets and custom settings.

TX-SR806_En.book Page 117 Monday, August 4, 2008 10:25 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-SR806 Seite 117

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-SR806

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info