Bedienungsanleitung Onkyo TX-SR806 (Seite 119 von 124) (Englisch)

63833

119

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

119

Troubleshooting—Continued

• If your TV is connected to the HDMI OUT, set the

“Monitor Out” setting to “HDMI” (page 41), and

select “- - - - -” in the “HDMI Input Setup” on page 44

to watch composite video, S-Video, and component

video sources.

• If your TV is connected to the COMPONENT VIDEO

MONITOR OUT, set the “Monitor Out” setting to

“Analog” (page 41), and select “- - - - -” in the “Com-

ponent Video Setup” on page 45 to watch composite

video and S-Video sources.

• If the video source is connected to a component video

input, you must assign that input to an input selector

(page 45), and your TV must be connected to either

the HDMI OUT or COMPONENT VIDEO MONI-

TOR OUT (page 25 and 34).

• If the video source is connected to an HDMI input,

you must assign that input to an input selector

(page 44), and your TV must be connected to the

HDMI OUT (page 34).

• While the Pure Audio listening mode is selected, the

video circuitry is turned off and only video signals

input through HDMI IN can be output.

• On your TV, make sure that the video input to which

the AV receiver/AV amplifier is connected is selected.

There’s no picture from a source connected to

an HDMI IN

• Reliable operation with an HDMI-to-DVI adapter is

not guaranteed. In addition, video signals from a PC

are not supported (page 34).

• When the “Monitor Out” is set to “Analog” (page 41),

and the “Output Resolution” (page 94) is set to any

resolution not supported by the TV, no video is output

by the HDMI OUT.

The onscreen menus don’t appear

• If your TV is connected to the analog outputs, set the

“Monitor Out” setting to “Analog” (page 41).

• On non-North American models, specify the TV sys-

tem used in your area in the “TV Format Setup” on

page 48.

• On your TV, make sure that the video input to which

the AV receiver/AV amplifier is connected is selected.

The picture is distorted

• On non-North American models, specify the TV sys-

tem used in your area in the “TV Format Setup” on

page 48.

The immediate display does not appear

• The immediate display will not appear when the input

signal from the COMPONENT VIDEO IN is output to

a device connected to the COMPONENT VIDEO

MONITOR OUT.

• Depending on the input signal, the immediate display

may not appear when the input signal from the HDMI

IN is output to a device connected to the HDMI OUT.

Reception is noisy, FM stereo reception is

noisy, or the FM STEREO indicator doesn’t

appear

• Relocate your antenna.

• Move the AV receiver away from your TV or com-

puter.

• Listen to the station in mono (page 59).

• When listening to an AM station, operating the remote

controller may cause noise.

• Passing cars and airplanes can cause interference.

• Concrete walls weaken radio signals.

• If nothing improves the reception, install an outdoor

antenna.

The remote controller doesn’t work

• Make sure that the batteries are installed with the cor-

rect polarity (page 14).

• Install new batteries. Don’t mix different types of bat-

teries, or old and new batteries (page 14).

• Make sure that the remote controller is not too far

away from the AV receiver/AV amplifier, and that

there’s no obstruction between the remote controller

and the AV receiver/AV amplifier’s remote control

sensor (page 14).

• Make sure that the AV receiver/AV amplifier is not

subjected to direct sunshine or inverter-type fluores-

cent lights. Relocate if necessary.

•

If the AV receiver/AV amplifier is installed in a rack or

cabinet with colored-glass doors, the remote controller

may not work reliably when the doors are closed.

• Make sure you’ve selected the correct remote control-

ler mode (pages 15 and 107-113).

• When using the remote controller to control other

manufacturers’ AV components, some buttons may

not work as expected.

•

Make sure you’ve entered the correct remote control code.

• Make sure to set the same ID on both the AV receiver/

AV amplifier and remote controller (page 93).

Can’t control other components

• If it’s an Onkyo component, make sure that the u

cable and analog audio cable are connected properly.

Connecting only an u cable won’t work (page 39).

• Make sure you’ve selected the correct remote control-

ler mode (pages 15 and 107-113).

• If you’ve connected an u-capable Onkyo MD

recorder, CD recorder, RI Dock to the TAPE IN/OUT

jacks, or an RI Dock to the GAME/TV IN jacks, for

the remote controller to work properly, you must set

the display to MD, CDR, or DOCK (page 50).

If you cannot operate it, you will need to enter the

appropriate remote control code (page 105).

• To control another manufacturer’s component, point

the remote controller at that component.

Tuner (TX-SR806 only)

Remote Controller

TX-SR806_En.book Page 119 Monday, August 4, 2008 10:25 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-SR806 Seite 119

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-SR806

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info