Bedienungsanleitung Onkyo TX-SR806 (Seite 120 von 124) (Englisch)

63833

120

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

120

Troubleshooting—Continued

• To control an Onkyo component that’s connected via

u, point the remote controller at the AV receiver/AV

amplifier. Be sure to enter the appropriate remote con-

trol code first (page 106).

• To control an Onkyo component that’s not connected

via u, or another manufacturer’s component, point

the remote controller at the component. Be sure to

enter the appropriate remote control code first

(page 105).

• The entered remote control code may not be correct. If

more than one code is listed, try each one.

• If none of the codes work, use the Learning function

to learn the commands of the other component’s

remote controller (page 114).

Can’t learn commands from another remote

controller

• When learning commands, make sure that the trans-

mitting ends of both remote controllers are pointing at

each other.

• Are you trying to learn from a remote controller that

cannot be used for learning? Some commands cannot

be learned, especially those that contain several

instructions.

Can’t record

• On your recorder, make sure the correct input is

selected.

• When the Pure Audio listening mode is selected,

recording is not possible because no video signals are

output. Select another listening mode.

There’s no sound

• Only components connected to analog inputs can be

played in Zone 2.

The sound changes when I connect my

headphones

• When a pair of headphones is connected, the listening

mode is set to Stereo, unless it’s already set to Stereo,

Mono, Direct, or Pure Audio.

The display doesn’t work

• The display is turned off when the Pure Audio listen-

ing mode is selected.

How do I change the language of a multiplex

source

• Use the “Multiplex” setting on the “Audio Adjust”

menu to select “Main” or “Sub” (page 83).

The u functions don’t work

• To use u, you must make an u connection and an

analog audio connection (RCA) between the compo-

nent and AV receiver/AV amplifier, even if they are

connected digitally (page 39).

The functions Auto Power On/Standby and

Direct Change don’t work for components

connected via u

• These functions don’t work when Zone 2 is turned on.

When performing “Automatic Speaker Setup”,

the measurement fails showing the message

“Ambient noise is too high”.

• This can be caused by any malfunction in your speaker

unit. Check if the unit produces normal sounds.

The following settings can be made for the S-

Video and composite video inputs

You must use the buttons on the unit to make these set-

tings.

1. While holding down the input selector button for the

input source that you want to set, press the [SETUP]

button.

2. Use the Left and Right [e]/[r] buttons to change

the setting.

3. Press the [SETUP] button when you’ve finished.

•Video Attenuation

This setting can be made for the DVD, VCR/DVR,

CBL/SAT, GAME/TV, or AUX input.

If you have a games console connected to the

S-Video or composite video input, and the picture

isn’t very clear, you can attenuate the gain.

Video ATT:OFF: (default).

Video ATT:ON: Gain is reduced by 2 dB.

Recording

Zone 2

Others

The AV receiver/AV amplifier contains a microcomputer

for signal processing and control functions. In very rare

situations, severe interference, noise from an external

source, or static electricity may cause it to lockup. In the

unlikely event that this happens, unplug the power cord

from the wall outlet, wait at least five seconds, and then

plug it back in again.

Onkyo is not responsible for damages (such as CD

rental fees) due to unsuccessful recordings caused by

the unit’s malfunction. Before you record important

data, make sure that the material will be recorded cor-

rectly.

For North American models, set the AV receiver to

Standby before disconnecting the power cord from the

wall outlet. For other models, set the AV receiver/AV

amplifier to Standby and the POWER switch to OFF

before disconnecting the power cord.

TX-SR806_En.book Page 120 Monday, August 4, 2008 10:25 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-SR806 Seite 120

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-SR806

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info