Bedienungsanleitung Optoma HQView-300 Series (Seite 23 von 30) (Englisch)

492719

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

T:+44 1274 394125 F: +44 1274 730960 E: techsupport@calibreuk..com 19

3.9.5. Switching Transition

When switching input channels by default the last frame of the prior displayed image is frozen and

displayed until a stable image of the new input channel can be shown. The switchover process is

supposed to be as seamless as possible. The source and monitor add switching noise due to

unforeseeable activity of the firmware in said devices. By default HQView is in auto frame rate switching

and I/O lock mode. In order to get a best smooth switching result with the source and monitor I/O lock

and auto frame rate switching have to be switched off in the Output/Display Type menu.

The switching transition of HQView can be set to Freeze, Blank, Fast Fade and Slow Fade. Freeze halts

the prior channel image until the new channel image is stable. Blank switches the output to show a

black screen instead of the last channel image. Fast and slow fade have the prior channel image faded

out and fade into the new channel video image once it is stable.

3.9.6. Menu Settings

This menu provides items to change the menu position and menu display time, i.e. the time after which

the OSD is switched off again with no user interaction. OSD Messages can be activated and

deactivated.

The menu language can be altered and the keypad can be locked. To unlock the keypad a combination

of keys has to be pressed at the same time. The locking of the keyboard is accompanied by the

message: Keypad is locked. Press Up/Down to unlock. When successfully unlocking the keypad the

message shows up: Keypad unlocked.

3.9.7. Network Settings

The Network Settings menu allows to configure the HQView-3xx TCP/IP address for communication

with e.g the warp generator PC tool. Under Address Type a static or DHCP leased address can be

chosen. The static address and Netmask need to be entered manually.

The Network Settings menu has a section with information on the DHCP Status and IP address

assigned to the board, as well as the fixed MAC Address programmed into the HQView-3xx. The DHCP

status is Off when static assignment is used or it displays an address when DHCP has leased an

address accordingly or it is None assigned if the lease was not successful.

Note: When changing from DHCP to Static mode or vice versa it is strongly recommended that

HQView-3xx is powered down after such a change, then powered back up, so that it is properly

recognised by other devices on the network.

In the Network Settings menu is a submenu Status Announce Setting. This feature is activated when

Enable Status Announce is switched on. HQView-3xx will then send messages out continuously through

RS232 and TCP/IP to signal system condition. Server address and port of the PC where to send the

message need to be entered. The Refresh Rate determines the rate at which the HQView-3xx status

condition and the message entered under Custom Data being sent out.

3.9.8. Factory Defaults

This button let you restore all settings to the default values of the HQView-3xx, thus, provide a means to

get back to a known (good) system state. A requestor will come up and ask to confirm prior to actual

restore.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Optoma HQView-300 Series Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info