Bedienungsanleitung Optoma HQView-500 Series (Seite 18 von 35) (Englisch)

492720

Zoom out

Zoom in

Vorherige Seite

1/35

Nächste Seite

T:+44 1274 394125 F: +44 1274 730960 E: techsupport@calibreuk..com 14

3.3.

Main Menu

The main menu lists the input channel select item, 6 sub menus, and a menu item for automatic setup

of VGA modes. The 6 sub menus are Output, Color, Geometry, PiP (HQView-500S) or Multiple Unit

(HQView-510 and 520/530), Enhancement and System.

On each menu page an Exit menu item is available to leave the menu or submenu. HQView-500S/510

and 520 also allow to leave a menu or submenu by pressing the up/down key simultaneously. HQView-

530 has a separate back key for this purpose.

Some adjustments are not applicable to all signal types or operating modes, in which case those non-

applicable functions will be ghosted and are not accessible via the menus.

All menus have a top status line and a bottom line indicating the firmware revision number. In the

status line the currently selected input channel is indicated and the detected mode is identified. The

firmware revision number displays the revision number of the bootloader behind BL, the revision

number of the firmware behind FW and whether it is a 500S, 510, 520 or 530 type HQView unit.

Navigating the menu system or changing values is done with the up and down keys in the case of

HQView-500S, 510 and 520 or a jog wheel in the case of HQView-530. In the following sections the

set-up method using the up and down keys is described.

To set up your HQView-5xx it is recommended that you follow this procedure:

Choose the correct output mode and parameters to suit your screen or projector.

Select the correct input signal.

Set the input levels and features appropriately to optimize the appearance of your image.

Set any other parameters to suit your application.

Note: All Input parameters are specific to your chosen input channel and input signal type, they are not

global to the unit. All Output parameters are global

3.4.

Input

The list of available inputs can be scrolled through using the Up and Down keys. The new input is not

selected until the Menu key is pressed. The list of inputs are: CVBS 1, CVBS 2, S-Video, Component,

VGA, 3G-SDI, DVI, HDMI and Test Pattern.

Test patterns can be generated by HQView-5xx without needing an input connected. When Test

Pattern is selected as the input, the required test pattern can be chosen with the menu navigation

up/down keys when the OSD menu is off.

3.5. Output

This menu contains adjustments associated with setting up outputs from the unit. The items are

organized in three sub menus, Display Type, Gamma/Color/Crush and Output Config. Use the up and

down keys to scroll to the required item and press the Menu key.

3.5.1. Display Type

Settings: LCD/Plasma, Projector

The Display Type setting defaults to Projector. Select Projector if you drive a projector and need the

warp function and edge blend capability. Set to LCD/Plasma if you do not need warp (including

Location). Multiple unit configurations with auto zoom are available, but without edge blend. The real

value of this mode is that the Flicker Filter becomes available. Note: For HQView-500S leave the

setting to Projector mode, since there is no difference to LCD/Plasma mode.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Optoma HQView-500 Series Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info