Bedienungsanleitung Oregon Scientific IB368 (Seite 16 von 19) (Englisch)

589257

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

heating in the room, if the room is damp, or if the speaker

is brought directly from a cold to a warm place. In this

case, leave the system turned off for a few hours until

moisture evaporates, unplug the AC power cord and then

plug it in again.

Alternatively, press the RESET button at the bottom of

the speaker to reset the unit and check to see if the unit

resumes operation.

How do I eliminate signal jamming?

Signals transmitted from devices such as a second iBall

nearby may jam with signals transmitted from the

transmitter dock to speaker. If signal jamming occurs,

follow the procedures outlined in the “RECOGNIZING

WIRELESS SIGNALS” section to set the RF mating

function between the speaker and transmitter dock.

The wireless speaker is powered on but why is it

not emitting any sound?

Check to ensure the power is on and increase the

volume. If there is still no sound, check to see if is lit

on the LCD. If it is, press the button on the speaker

control panel to unmute the speaker.

Data signal interference or static electricity may disrupt

the signal reception from the audio source. Power off

the speaker, wait a few seconds, and turn the unit back

on. Alternatively, press the RESET button at the bottom

of the speaker to reset the unit.

Why is the wireless speaker not responding when

the buttons are pressed?

Remove and reconnect the AC power plug or reinsert the

batteries and switch the speaker on again, checking that the

power is on. If there is still no response, the speaker’s control

panel membrane may be damaged. Take the unit to a

qualified Oregon Scientific dealer for servicing.

Alternatively, press the RESET button at the bottom of

the speaker to reset the unit.

Why are the rechargeable batteries not charging?

The correct AC adapter should be plugged into the

wireless speaker.

Ensure that a battery cap must be placed on top of the “

”

terminal of a battery. The battery with the cap must be

positioned into the specified battery slot of the battery

compartment with the other batteries installed as normal.

Do not use the battery cap if the speaker is powered by

alkaline batteries. Doing so may increase the risk of fire,

personal injury, or damage to the speaker.

When placing the batteries into the compartment, make

sure to correctly align the polarities.

My iPod is docked to the transmitter dock but why

is nothing happening?

The iPod may not be inserted properly into the transmitter

dock. Remove the iPod and reinsert, making sure to

correctly align its pin connectors with those of the

transmitter dock. Or, the docking tray inserted into the

NOTE Depending on the nature and strength of signal

jamming, the process may need to be repeated several

times before RF mating is successful.

TROUBLESHOOTING

Use this troubleshooting guide to help you remedy any

difficulties you may be experiencing while using the iBall.

Should any problem persist after you have checked these

symptoms, consult your nearest Oregon Scientific dealer.

Why does the wireless speaker not power on at all?

Ensure the power cord is firmly plugged into the power

outlet. On the rare occasion, the unit may not operate

due to data signal interference or static electricity. Turn

the power off and unplug the unit from the power outlet

briefly, and then plug it in again so it will reset itself and

turn the speaker on.

Why does the power keep turning off after turning

on?

The batteries may have run out of power or are not

correctly aligned with their polarity. For alkaline batteries,

re-install checking the polarity; if the unit still does not

operate, insert new alkaline batteries into the unit.

For rechargeable batteries, plug the AC adapter so the

speaker can operate on AC power and recharge the

depleted batteries.

How do I eliminate the severe hum, distortion or

noise that is coming from the wireless speaker?

The speaker may be positioned too closely to the audio

source, such as a TV or radio. Move the speaker at least

1 meter (approx. 3 feet) away from the source.

Check that the speaker’s position and connections are

clear of any strong magnetic fields or radio frequencies

such as Bluetooth, wireless LAN, microwaves or

fluorescent light, which may interfere with reception.

Similarly, make sure the speaker is not placed near any

2.4GHz DECT phones or mobile phones, whose

frequencies can interfere with wireless transmission

between the remote control device and speaker.

The plugs and jacks may be dirty, affecting the

connections and thus causing sound distortion. Wipe

clean. In some cases, volume might not be appropriately

adjusted. Adjusting the volume will help to clear any hum

or distortion.

There may be excess moisture condensed inside the

speaker or on the speaker grill that might affect the unit’s

ability to produce audio, especially after turning on

EU_IB368manual(eng)R12 8/31/2005, 3:51 PM15

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oregon Scientific IB368 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Oregon Scientific IB368

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info