Bedienungsanleitung Oregon Scientific WMR300 (Seite 5 von 15) (Englisch)

677397

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

BAROMETER

2 3

8 7

4 5

1. Altitude area indicator

2. : Alarm for changes of barometric pressure

3. TODAY/MONTHLY/MIN/MAX: Display the maximum/minimum of today’s/

monthly barometric pressure reading

4. Barometer trend

5. Hourly records indicator (From -24 to 0)

6. inHg / mmHg / mb / hPa: Barometer unit

7. M / FEET: Altitude unit

8. Barometer reading

RAINFALL

8 7 6

1 2

1. HI alarm: Alarms for high rain rate and past 24-hour rainfall.

2. TODAY/MONTHLY/MAX: Display the maximum of today’s/monthly rainfall/rain

rate reading

3. Hourly records indicator (From -24 to 0)

4. RATE: Rainfall rate

5. THIS HOUR/ACCUM/PAST 24hrs: Selected time range

6. In/mm: Rainfall unit; In/hr / mm/hr: Rain rate unit

7. Rain reading display

8. Rain area indicator

INSTALLATION

Please prepare some tools before starting your installation. You may need some

types of screw drivers, wrenches or an electric drill.

SET UP RAIN SENSOR & THERMO / HYGRO SENSOR

The rain gauge collects rain and takes rainfall readings. The transmitter box can

wirelessly transmit data to the main unit.

1. Make sure the engraved arrow on the thermo/hygro sensor casing towards the

installation direction of the transmitter box.

2. Align three screw holes on the rain gauge with the three double end studs on

the thermo/hygro sensor casing.

3. Tightly twist the type B screws into the double end studs to make sure the

connection is ﬁrmly.

4. Put the rain collector on the rain gauge

aligning the tipping with the holes, and

then twist clockwise to secure it tightly.

Put the plastic debris ﬁlter in the rain collector

NOTE

Cut away the cable tie on the tipping

bucket before using.

SET UP WIND SENSOR

The wind sensor takes wind speed and direction readings.

1. Loosen the screws in the wind cups and wind vane.

2. Insert the top of the wind sensor unit into the wind cups securely with some

pressure and then twist the screw tightly.

3. Insert the bottom of the wind sensor unit into the

wind vane securely with some pressure and then

twist the screw tightly.

NOTE

There is a rubber washer around the top of

the wind sensor for preventing from hard touching

during installation. You can move up the rubber

washer a little bit before inserting the wind cup.

SET UP TRANSMITTER BOX

1. Approach the mounting ring of the transmitter box to the rain gauge, and align

mounting ring with the bottom of the hole of the rain gauge.

2. Insert the mounting insert into the mounting ring of the transmitter box through

the hole of the rain gauge with some pressure. A click sound can be heard.

NOTE

The transmitter box contains sophisticated electronic parts, so you must

treat it with care.

CABLE CONNECTIONS

It is better you connect the cables of each sensors

to the transmitter box before positioning the pole.

1. Unscrew to open the transmitter box.

2. Take off the rubber stopper from the cable slot.

3. Insert all the sensor cables through the cable slot.

4. Plug each sensor cable into corresponding

socket that has name below the socket for

recognition. A click sound can be heard.

5. Return the rubber stopper to the cable slot.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oregon Scientific WMR300 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Oregon Scientific WMR300

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info