Bedienungsanleitung Oregon Scientific WMR300 (Seite 7 von 15) (Englisch)

677397

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

1.5M

7. Follow the instructions in sections of Cable Connections, Transmitter Box-

Battery Installation and Channel Setting.

8. Securely locate the pole in your desired outdoor area.

9. Route the excessive cables neatly by using the provided cable ties.

NOTE

6 meters wind sensor cable is provided for you to locate the wind sensor

separately from the pole like in Option 2 and Option 3. Route the excessive

cables if necessary.

NOTE

Put the plastic debris ﬁlter into the rain collector. Please check the ﬁlter

regularly and ensure it is not fully covered by the leaves or other objects.

Option 2: Wind sensor is installed

separately; other sensors with transmitter

box are installed on a pole.

1. Follow the steps 3-4 in Option 1 to

install the temperature/hygro sensor

and rain sensor on a pole.

2. Insert the Type A screws into the wind

sensor. Securely screw them into your

desired location using wrench.

3. Follow the steps 7-9 in Option 1 to

complete the installation.

Option 3: Excepting wind sensor is

installed on a pole; other sensors with

transmitter box are installed separately.

1. Follow the steps 5-6 in Option 1 to install

the wind sensor on a pole.

2. Insert the Type A screws into the rain

gauge. Securely screw them into your

desired location using wrench.

3. Follow the steps 7-9 in Option 1 to

complete the installation.

MAIN UNIT-BATTERIES INSTALLATION

To insert batteries:

1. Remove the battery compartment cover.

2. Insert the supplied batteries in the compartment, matching the polarities (+ / -).

3. Press RESET in the compartment.

4. Close the battery compartment cover.

NOTE

Do not use rechargeable batteries. It is recommended that you use alkaline

batteries with this product for longer performance.

Low battery indicators:

Icon Meaning

Main unit batteries low

Transmitter box(es) batteries low

Transmitter box(es) / main unit batteries low

For continuous use, install the power adapter. The batteries are for back-up use only.

Plug the power adapter into an electrical outlet not controlled by a wall switch.

Power Adapter

NOTE

The power adapter is intended

to be correctly oriented in a vertical or

ﬂoor mount position. The prongs are not

designed to hold the plug in place if it is

plugged into a ceiling, under-the-table or

cabinet outlet.

PAIRING SENSORS / REMOVE SENSORS

To pair a sensor:

1. The SW4 pairing switch in transmitter box is set to 1 (ON).

2. Press

area.

3. Press and hold

and at a time until you enter sensor setup

mode. (All sensor readings disappear on the screen,

- - displays on the screen.)

Press or to select the channel you want to add the sensor.

The channel in dash mode (

displays) is available for pairing a sensor.

5. Press and hold

for 2 seconds. There is a beep. Press anywhere on

the panel not in area.

6. SEARCH indicator in area ﬂashes to do pairing.

7. When

SEARCH disappears and the selected channel of sensor displays the

weather reading on the screen, the pairing is complete and successful.

NOTE

The main unit searches the sensor for about 10 minutes. Please complete

the pairing within an hour after you switch on the pairing switch in the transmitter box.

Otherwise, you need to turn off the pairing switch, and then switch it on again.

NOTE

Make sure you calibrate the direction of wind vane on the wind sensor after

adding sensors, see Direction Calibration for details.

TIP

The transmission range may vary depending on many factors. You may

need to experiment with various

locations to get the best results.

Make the antenna of the transmitter

box and the one on the main unit

be paralleled to get a better pairing

performance.

To remove a sensor:

1. Press

area.

2. Press and hold

and at a time until you enter sensor setup

mode. (The weather reading disappears on the screen, - - displays on the screen).

3. Press

or to select the channel of the sensor you want to

remove. You can only remove the sensor that the reading is not in dash mode

( displays).

4. Press and hold

for at least 2 seconds. There is a beep and then the

screen shows - -, the sensor is successfully removed from the main unit.

CLOCK

MANUALLY SET CLOCK

NOTE

To set the clock/calendar manually, disable the clock signal reception ﬁrst

(see To Enable / Disable signal reception).

To manually set the clock / calendar:

1. Press

area to activate. displays next to the area and the tool bar

displays at the below of the screen.

2. Press and hold

on the tool bar, then toggle between

time zone offset, day time saving options, 12/24 hr format, hour, minute, year,

day/month format, month, day, weekday, language, latitude and longitude .

3. Once in desired setting, press

or to change the settings.

4. Press:

• to conﬁrm and continue to next setting

• Touch panel area (except tool bar) to conﬁrm and exit.

NOTE

For WMR 300, the range of time zone offset is between -12 and +12. You

should manually input the time zone of your location, please check your local

weather observatory for detail. For example, Hong Kong should be set to +8.

NOTE

The language options are English (E), Russian (R), Spanish (S), Italian (I),

German (D) and French (F).

NOTE

You need to input latitude and longitude of your location. Please refer to

your local weather observatory website. The latitude and longitude input affects

the sunrise/sunset time.

Oregon Scientific WMR300 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Oregon Scientific WMR300

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info