Bedienungsanleitung Oxford OF690 HotGrips (Seite 5 von 42) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

606569

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

Oxford Hotgrips instructions v.8 switch - 09/07/12

5. Be sure to act immediately to wipe away any excess glue with a dry cloth.

6. Allow the glue to dry for at least 24 hours before using. Ensure that the grips are rmly xed in place before use.

Do not use if the grip moves and seek advice immediately.

H: Wiring Harness Installation

1. Find a suitable location to mount the switch and then take the wiring back to the battery.

2. Install the switch in a suitable position ensuring the wires from the grips reach without strain.

3. The switch may be mounted on a at panel using the self adhesive mounting foam pad. It may also be mounted on

the metal bracket supplied (if the bracket is suitable for the vehicle). Please t the foam pad between the bracket

and switch to reduce vibrations. The bracket may also be bent to a different shape if required.

4. On many bikes it is possible to t the bracket to the clutch clamp as shown below using the longer bolts provided.

5. The loom is designed for ease of tting. There are only 2 wires that need attaching to the motorcycles existing

wiring system. All other connections are through the multi pin block connectors and cannot be ﬁtted the wrong way.

6. We recommend that the wiring loom is positioned away from existing wiring looms on the motorcycle to avoid any

possible electrical interference issues.

7. When the wiring is in position on the motorcycle, we strongly recommend that all connectors are protected with

either electrical insulation tape, waterproof sealing tape or heat shrink tubing (be careful not to damage the cable

when tting heat shrink).

8. Both the negative and the positive battery connections are tted with a ring terminal. This will allow them to be

bolted to the battery terminals. It is both preferable and the easiest option to connect the positive (+ Red wire)

straight to the positive (+) battery terminal so that the switch receives sufcient voltage from the vehicles charging

system.

9. The negative or earth (Black wire) should be connected to the negative (-) battery terminal.

10. If the switch must be connected to a switched ignition supply feed, please ensure that the wiring harness is

connected to main ignition cabling which can take the extra load of up to 4 amps. Problems are commonly found to

be caused when connections are made to horn or any lighting circuits.

Typical problems experienced could be:

- The switch may not come on

- Fuses failing in the fuse box

- Overheating of wires on the bike

- Indicators or lighting malfunctioning

If unsure, please contact your local dealer for advice before ﬁtting these Hotgrips.

Refer to the wiring diagram on the next page.

Install the HotGrip Switch

as shown using the optional

bracket (OF91)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oxford OF690 HotGrips Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Oxford OF690 HotGrips

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info